Sunrise Telecom Sunset Xdsl Tester 2 Module New Loaded

US $1,400.00

Hallandale, Florida, United States
Jan 29th

Open on mobile:
QR code

SquareTrade © AP6.0 TYPE: xDSL VERSION: S2.01S OPTIONS: AA0 AD7 AG AA0: Regular Set AD7: TDR/Line/DMM AG: TDR J TESTED: New WORKING: New PHYSICAL CONDITION: New WHAT'S INCLUDED: (1) xDSL Meter with Battery ((new)) (1) Protective Cartridge ((new)) (1) 8MB Software Cartridge with options- AA0 AD7 AG ((new)) (1) Rubber Impact Protective Case ((new)) (1) Clip-on Strap ((new)) (1) Alcatel ADSL ATU-R MODULE SSxDSL-3 ((new)) (1) 10BASE-T SDSL Module SSxDSL-7 ((new with protective case)) ((new)) (1) AC Power Supply ((new)) (1) Double Compartment Transport Case ((new)) (1) Sunrise xDSL Product Training CD ((new)) (1) Sunrise xDSL User's Manual ((new)) (1) Alcatel ATU-R Module SSxDSL-3 User's Manual ((new)) (1) SDSL Module SSxDSL-7 User's Manual((new)) (3) Quick Refference Cards ((new)) (1) Warranty Registration Card (1) DC Car Charger (( AVAILABLE ONLY WITH BUY IT NOW OPTION )) COMMENTS: Why buy a used one, when you can get a new one at this price. I will include a car charger with buy it now option or you can purchase it separately for $60.00 THIS IS A NEW UNIT. REASONABLE OFFERS ONLY. I WILL ANSWER ALL QUESTIONS. I'VE LISTED ALL RELATED INFORMATION ON THIS ITEM. INTERNAL USE: BRAND: MODEL# PART# SUNRISE TELECOM xDSL ADDITIONAL PICTURES --------------------------------------------------------------------------------------- MANUFACTURE'S INFO' AND SPECS. These specs are based on overall testing capabilities of the meter. Modules and/or software are required for each option. The module and software version will depicts the meter's capabilities. Product Specs: ADSL Testing IDSL Testing SDSL Testing HDSL Testing G. SHDSL Testing HDSL2 Testing T1 Testing IP Testing Datacom Testing VF TIMS Testing PSD Noise and Frequency Response Time Domain Reflectometer Digital Multimeter ISDN BRI Testing ISDN PRI Primary Rate GR-303 HSSI (High Speed Serial Interface) Testing SunSet xDSL Chassis Configurations: The SunSet xDSL, in its 3 lb (1.36 Kg) platform, provides incredible versatility for a handheld test set. Plug-in modules allow you to customize the test set for your specific needs. The modular platform significantly extends the life of your test equipment investment; you simply modify your test set with a new plug-in module whenever new technologies evolve. ADSL Testing: Standards Supported: ANSI T1.413 ITU G.992.1 (G.DMT) ITU G.992.2 (G.lite) CAP (TR-59) ATU-R Mode: Synchronize and achieve "showtime" with DSLAM ATU-C Verify service rate provisioning with acceptable noise margins Determine what rates can be supported before installing equipment ATU-C Mode: Prequalify cable using G.DMT, ANSI, or G.lite compliant ADSL signal Know what rates can be supported before installing equipment Systems Supported: Various ADSL systems are supported. Please inquire with your local sales representative for correct HW/SW selection. IDSL Testing The IDSL Module offers an effective combination of features for IDSL and BRI ISDN testing, circuit turn-up and troubleshooting can be done so easily. External clock input ensures stable BER measurement on IDSL circuits over Digital Loop Carrier (DLC) system testing. Offering the emulation modes you need most to complete IDSL testing at the Central Office and at the customer premises. The straightforward configuration and menu-driven operation make using the IDSL Module test functions simple. IDSL testing capable is not the limit of the IDSL Module, which also offers a broad range of crucial ISDN and X.25 over D-channel Basic Rate test capabilities making circuit testing more productive. Highlights: U and S/T Interfaces IDSL Testing ISDN Testing External clock for IDSL over DLC Testing U interface eoc Commands U interface M4 Channel Access Telephone Function ISDN Call Functions BERT Measurements Automated Tests D-channel Packet SVC and PVC Tests Equipped with the most needed test capabilities the IDSL Module enables field technician to efficiently perform circuit turn-up and troubleshoot testing for IDSL and BRI ISDN circuits. Turn-up or troubleshoot IDSL circuit by running end-to-end BERT or single-ended BERT from the central office to the customer premises direction. Use external clock inputs to facilitate IDSL over DLC system testing to ensure valid BERT measurement. Test and monitor IDSL circuit status with the U interface eoc commands and M4 channel access capability provided by the IDSL Module. Turn-up ISDN circuits by making test calls and using the automated test capability Troubleshoot ISDN circuits by monitoring the D channel messages and call disconnect cause value. Verify proper circuit functioning of X.25 over D channel by making test calls and sending data packets. U and S/T Interfaces The IDSL Module allows IDSL and ISDN BRI testing by providing both U and S/T test interfaces. IDSL Testing IDSL circuit testing generally requires both LT and NT emulation modes when testing from the Central Office and from the Customer Premises directions. The dual mode U 2B1Q interface supports both LT and NT emulation modes for U interface testing supporting test requirements at either site. BER test on selected test channel allows transmission quality assessment of the IDSL circuit. IDSL testing on the S/T interface is also supported through the availability of the S/T interface and the associated NT and TE emulation modes. ISDN Testing Considering also ISDN circuit turn-up and maintenance testing requirements, the ISDN BRI emulation modes provide Layer 2 and Layer 3 testing with the TE/NT1 and TE-S/T emulation respectively for the U and S/T interfaces. External Clock for IDSL Circuit over DLC Testing Transmission quality BERT performed on IDSL circuits carried over Digital Loop Carrier (DLC) systems mostly suffers from intermittent pattern sync loss owing to clock slip problem. The IDSL Module provides external reference clock inputs to enable the test set to synchronize to the network to eliminate clock slip between the source from the test set and the circuit under test ensuring valid BER test result. U Interface eoc Commands Perform loop BER test from the central office or co-locate site towards the span with the repeater or NT looped-up after sending eoc loopback command. Verify also if the NT is connected to the circuit by checking the response of the eoc command. Acts as loop box in NT mode responding to eoc loopback commands from the LT. U Interface M4 Channel Access The M4 channel provides useful information to the field technician about the circuit continuity through to DSLAM. The IDSL Module offers control and monitor of the M4 channel bit status. Telephone Function Telephone function for ISDN testing is supported through the use of microphone and loudspeaker on the SunSet xDSL unit. A handset interface is provided on the module for connection of an external handset to allow communication on two simultaneous calls. ISDN Call Function Supports most needed service types. Convenient B channel selection is provided for outgoing calls for test of individual B channel. Automatic last number recall and speed dial numbers are available for easy access to last called and commonly used test numbers. BERT Measurements BER test analysis is in accordance with ITU-T Rec. G.821 to determine the performance of the end-to-end connection. BER test results can be stored in non-volatile memory. Automated Tests The ISDN automated tests are ideal for service provisioning to enable a quick verification of the services associated with and the performance of the line under test. Tests include Auto SPID for National ISDN, Guess SPID, Service Scan, Supplementary Service Scan, SELF-BERT, DUAL-BERT. D-channel Packet Test The X.25 over D-channel test function supports testing for SVC and PVC service. Data transmission is verified by sending pre-defined data packets. On screen indication confirms successful packet transmission making packet test easy. SDSL Testing Systems Supported Lucent Copper Mountain Nokia Others to follow Chipset Based on Conexant chipset HTU-R mode: Synchronize with HTU-C line card Install and verify SDSL service HTU-C mode: Prequalify a line for SDSL service Plug and play with far end HTU-R HDSL Testing The HDSL Module offers a set of strong test features for 4-wire HDSL span installation and maintenance. It provides you with handy T1 testing capabilities through the HDSL interface and also the DS1 interface giving a total solution for testing on both the HDSL and DS1 interfaces all in one box. Extensive HDSL span loopback control capability combined with the user-friendly graphical result presentation makes testing more efficient and productive. Highlights HDSL Testing HDSL Span Performance DS1 Testing HDSL Span Loopback CSU & NIU Loopback BERT Measurements The HDSL Module brings you the test solution for both 4-wire HDSL and DS1 span testing: Pre-qualify cable pairs for HDSL modem installation to ensure required transmission performance can be achieved. Verify proper functioning of the HDSL central office terminal and remote terminal by replacing the HDSL terminal with the HDSL Module. Troubleshoot HDSL span by verifying span performance parameters against circuit turn-up record. Test HDSL span by running BERT to local and remote terminals after loop-up. Test T1 and fractional T1 circuits with the DS1 interface and BER test capability. Verify T1 span performance by in-service monitoring the frame and code error of the signal in bridge or monitor mode. HDSL Testing The HDSL Module provides comprehensive 4-wire HDSL span testing capabilities. HTU-C and HTU-R emulation modes are available for out-of-service span performance evaluation. The integrated T1 tester is available to facilitate the BER performance evaluation of HDSL span and also the performance of the far end terminal without the need of another T1 tester. HDSL Span Performance Noise margin, pulse attenuation are important parameters for a HDSL span to determine the performance of the span during span turn-up and for maintenance troubleshooting. The HDSL Module displays on-screen with regular automatic updates these parameters for both of the two HDSL loops eliminating the need for a craft terminal. DS1 Testing The need for T1 testing on DS1 interface is very common for both HDSL span and T1 span turn-up and troubleshooting. The HDSL Module provides a DS1 interface for such a test requirement. Framed, unframed, full rate and fractional T1 configurations are available to meet various test requirements. HDSL Span Loopback Loopback control function is required to enable single-ended BERT testing on the HDSL span. Powerful HDSL loopback features are available in the HDSL Module to enable remote loopback control in HTU-C mode or T1 test mode. The graphical user interface provides an easy-to-master loopback control function for HDSL span testing. CSU & NIU Loopback The HDSL Module allows loopback control of the remote CSU and NIU to make single-ended BERT of the span convenient. Pre-existed loop detection is provided to provide a clear loopback status before and after the transmission of the loopback commands. BERT Measurements Error performance analysis is in accordance with ITU-T Rec. G.821 to determine the transmission performance of circuit. Bit, frame and BPV error injections are available to verify circuit continuity and test device interface. G.SHDSL Testing G.SHDSL is an ITU standard that defines high speed, symmetrical DSL delivery over a single copper pair (2 wire operation) at rates between 192kbps and 2.312Mbps. Highlights STU-R Emulation STU-C Emulation Loop Prequalification Standards Supported ITU G.991.2 STU-R Emulation Link turn-up with DSLAM Verify service rate provisioning with acceptable noise margins Determine what rates can be supported before installing equipment Service verification to ISP STU-C Emulation Link turn-up with CPE equipment Verify service rate provisioning with acceptable noise margins Service verification Loop Prequalification Prequalify a dry copper pair Know what rates can be supported before installing equipment HDSL2 Testing HDSL2 is an ANSI T1.418-2000 standard that defines high speed, symmetrical DSL delivery over a single copper pair (2 wire operation) at fixed T1 rates. Highlights H2TU-R Emulation H2TU-C Emulation Loop Prequalification H2TU-R Emulation Link turn-up with DSLAM Verify service rate provisioning with acceptable noise margins Service verification to ISP H2TU-C Emulation Link turn-up with CPE equipment Verify service rate provisioning with acceptable noise margins Service verification Loop Prequalification Prequalify a dry copper pair Know what rates can be supported before installing equipment T1 Testing - Dual T1 Module The Dual T1 Module offers full T1 physical layer testing via a standard dual T1 interface. The user can install and maintain T1 networks by testing T1 transmission, signal levels, and alarm signals. Optional services include VF, datalink, and intelligent repeater control for more power and flexibility. Highlights Comprehensive T1 Transmission Testing Loopback Testing for T1 Circuits Voice and Signaling Testing ESF Data Link Control ISDN Primary Rate GR303 Comprehensive T1 Transmission Testing Complete transmission testing is the foundation of the SunSet xDSL Dual T1 Module. T1 and FT1 BERT testing includes all standard industry test patterns, including FOX, 55OCTET, and 55DALY. Results include bit errors, alarms, BPVs, CRCs, simplex current, frequency, and level. Auto configuration makes setup quick and easy. Full duplex T1 testing: bi-directional monitoring and drop & insert testing Complete stress patterns and measurements Frequency graph illustrating clock slips and wander Loopback Testing for T1 Circuits A complete set of network loopback codes includes CSU and NIU. User-programmable codes provide extra flexibility. The Dual T1 Module also contains intelligent repeater control for Westell and Teltrend equipment, allowing T1 span troubleshooting. Inband and datalink commands for CSU and NIU equipment 10 user-programmable loopback codes Voice and Signaling Testing The SunSet xDSL Dual T1 Module is the perfect tool for installing and maintaining voice trunks. By placing and receiving calls, the Dual T1 Module verifies service when installing new voice trunks or PBX equipment. Bi-directional monitoring and drop/insert testing troubleshoots signaling problems between the switch and the PBX. Features include: Dialing: DTMF, MF, DP E&M, Loop-start, Ground-start, FXO/FXS signaling Send/receive test tones Noise measurements: signal to noise, C-notch, C-message, 3K-flat Digits capture and analysis Bi-directional signaling analysis ESF Data Link Control Monitoring the ESF BPM-PRM data link is an excellent way to discover errors which are otherwise undetectable at the monitoring point. The user can also retrieve valuable performance reports from NIUs. ISDN Primary Rate The Dual T1 Module has the power and features to troubleshoot PRI problems, whether the cause be physical layer errors, timing, switch translations, or other protocol issues. In addition to bi-directional trace monitoring and decoding, the Dual T1 Module can place and receive both voice and data calls in a TE or NT configuration. PRI Highlights TE/NT Emulation National ISDN, AT&T Custom, and Nortel DMS 23B+D, 47B+D, or 46B+2D testing BERT data calls: 56k, 64, Nx64k Backup D-channel test for NFAS circuits D-channel monitor with full decode Trace filtering and storage GR-303 The Dual T1 Module offers testing for all aspects of GR-303 systems: monitoring the TMC/CSC control channel, viewing robbed ABCD signaling and dialed digits, listening to voice channels, and thorough tests for the physical layer. The GR-303 option troubleshoots signaling problems between the switch and remote terminal: to determine call status, monitor for any dropped calls, detect any abnormal conditions, and identify when service was unavailable. IP Testing: The IP module provides an efficient way to verify end to end provisioning from the customer ADSL modem to the far end ISP gateway and beyond. PING Test: Verifies provisioning and IP connectivity all the way to the customer's ISP. The IP module offers Service Level Agreement (SLA) verification between the ISP and the customer. This verification is critical for business customers with minimum bandwidth guarantees. Throughput Test: This application is designed to verify the available upstream and downstream bit rates between the ISP gateway and the customer premises. The SunSet user can generate a specific load, measure the quality of the transfer, and determine the bit rate limit separately in each direction, thus verifying the SLA separately for both upstream and downstream transmission. This asymmetric load test is superior to ATM cell loopback methods of other vendors which can only verify connectivity but cannot verify full bandwidth asymmetric transmission in both upstream and downstream directions. Datacom Testing The Datacom module expands the SunSet xDSL's applications to testing WAN/data services. DTE/DCE emulation extends end-to-end testing of data networks and can be used to install and verify CSUs, routers, and other WAN equipment at the CPE. B-directional monitoring provides a greater level of troubleshooting for data networks. Applications include: DTE/DCE emulation Bi-directional monitoring with Y-adapter V.35, RS232, RS449, RS530, X.21 Data rates from 50 bps to 2.048 Mbps BERT testing with stress patterns Control lead status for CTS, RTS, DSR, DTR Loopback testing with RL & LL DTE Emulation DTE emulation provides end to end testing for data networks. This can be done in either a point to point configuration or the set can loopback a DCE device (RL & LL) for one-sided testing. Bi-directional Monitoring With Y-adapters the SunSet xDSL can monitor the data sent by the DTE and DCE devices. Users may view control lead status (CTS, RTS, DSR, DTR) from both sides, as well as view the actual data bits sent. Other valuable monitor measurements include data loss and received frequency. VF-TIMS Testing VF-TIMS module offers as an additional application to the SunSet xDSL product. The VF-TIMS module provides complete Voice Frequency testing in the analog voice range. It supports a range from 50Hz to 20,000Hz, and has tests for received level and frequency, noise, signal to noise, impulse noise, and call setup (DTMF, DP, or MF Dialing). Applications include: Transmission/Receive Frequencies and Level measurements 3-Tone Slope and Frequency Sweep functions Noise and Signal to Noise ratio Measurement Impulse Noise measurement Call Placing for Analog circuit testing Transmission /Receive Frequencies and Level measurement One basic application is to transmit a frequency over a pair of wires. Typically another test set is needed to measure the frequency at the far end of the cable. This function of transmitting frequencies includes a number of ways this can be done: Fixed Mode: This is a single fixed frequency being sent at a fixed level. 3-Tone Slope Mode: This mode sent frequency 404, 1004, and 2804 Hz at 5 seconds interval with a fixed level. Sweep Mode: This sweeps a certain range of frequencies with a user configurable start and stop frequencies, a step, a dwell time, and a fixed level. Quiet Mode: This places a quiet termination on the circuit. Another basic application is to receive a frequency and perform a level measurement. This strictly shows received frequency and level. Noise and Signal to Noise ratio Measurement, and Impulse Noise Measurement VF-TIMS module can perform Noise and Signal to Noise ratio measurement, and Impulse Noise measurement with different filters placed on receiver. These filters are C-message, 3kHz-Flat, and 15kHz-Flat. This test is typically done on one of the cable with a Transmit source on the other end of the pair, and this test can be done either 2-wire or 4-wire cable. Call Placing for Analog circuit testing: VF-TIMS module allows you to place a call on a 2 wire analog POTS circuit with selected dial mode (DTMF, DP, or MF dialing). This will be done connected to a switch in a central office where digits are sent and you can talk and listen with the test on line. Cable Maintenance Testing: Independent cable assessment features for installation, prequalification, and troubleshooting. Digital Multimeter: Capacitance Resistance AC Voltage DC Voltage Loop Resistance Capacitive Balance Load Coil Detector: PSD Noise and Frequency Response Background Noise: PSD and IEEE-743 Filters Frequency Response/Insertion Loss Impulse Noise Signal-to-Background Noise Level and Frequency Meter Frequency Generator HSSI Testing: The HSSI module provides High Speed Serial Interface (HSSI) testing for speeds up to 52 Mbps. Applications: DTE Emulation BERT Testing Loopback Testing: generate loopback commands (LA and LB) and auto-response to received loopback commands (LC). Control DTE transmit control leads and monitor received DCE control leads. Other Info: The Sunrise SunSet XDSL Portable Test Set helps ensure timely delivery of Digital Subscriber Line service. The modular chassis supports a variety of plug-in modules that address a number of different transmission technologies, including ADSL, IDSL, SDSL, HDSL, Voice Frequency, and Datacom. Additionally, powerful Cable Maintenance Testing (CMT) features enable comprehensive cable quality measurements. Best of all, the Sunrise SunSet XDSL Portable Test Set can be tailored to suit your needs. The Sunrise SunSet XDSL Portable Test Set, in its 3 lb (1.36 Kg) platform, provides incredible versatility for a handheld test set. Plug-in modules allow you to customize the test set for your specific needs. The modular platform significantly extends the life of your test equipment investment: you simply modify your test set with a new plug-in module whenever new technologies evolve. Option Description: ADSL/ATUC: Module AA0: Regular Set AB1: Ping all AD7: TDR/Line/DMM AF: Remote Auto Set AG: TDR CD: CH: MAIN UNIT DESCRIPTION These prices and information are from the manufacture and are listed as refference only. Part Number Category For Description SSxDSL Chassis SunSet xDSL SunSet xDSL Full Chassis. Cable Maintenance Test (CMT) features include: LINE, TDR, DMM features. Supports Plug-in Modules. Includes standard accessories: Internal NimH battery (SS140), Universal Charger (SS138D), 2-prong power cord (SS145A), User’s Manual (SS160), software cartridge, Protective Cartridge (SW2504) for 2nd Memory card slot. Includes 3-year warranty on chassis, 1-year warranty on battery and accessories. CLEI: VATSBD0BAA CPR: 774233. See details SSxDSL-L Chassis SunSet xDSL SunSet xDSL Light Chassis. Supports Plug-In Modules. Chassis does not support Line, TDR, DMM features. At least one Plug-in Module is required. Includes standard accessories: Internal NimH battery (SA141), Universal Charger (SS138D), 2 prong power cord (SS145A), Users Manual (SS160M), software cartridge, Protective Cartridge (SW2504) for 2nd Memory card slot. 3-year warranty on chassis, 1-year warranty on battery and accessories. CLEI:VATSBVOBAA CPR:774342. See Image SSxDSL-M Chassis SunSet xDSL SunSet xDSL Module Chassis. Supports Plug-In Modules. Includes Load Coil Detector feature. Factory upgradable to support LINE, TDR, DMM features. At least one Plug-In Module is required. Includes standard accessories: Internal NimH battery (SA141), Universal Charger (SS138D), 2-prong power cord (SS145A), Users Manual (SS160M), software Cartridge, Protective Cartridge (SW2504) for 2nd Memory card. 3 year warranty on chassis, 1-year warranty on battery, and accessories. CLEI: VATSBVOBAA CPR: 774342. See Image MODULES / SOFTWARE DESCRIPTION These prices and information are from the manufacture and are listed as refference only. Part Number Category For Description SSxDSL-1 Module SunSet xDSL PairGain T1 HDSL Module. CLEI: VATSCEABAA CPR: 774234 See_Image SSxDSL-2 Module SunSet xDSL ADSL ATU-R Module. CLEI: VATSDW0BAA CPR: 774343 See_Image SSxDSL-3 Module SunSet xDSL Alcatel ADSL ATU-R Module. CLEI: VATSDGABAA CPR: 774236 See_Image SSxDSL-4 Module SunSet xDSL Alcatel ADSL ATU-C Module. CLEI: VATSGR0BAA CPR/OFC: 774298 See_Image SSxDSL-5 Module SunSet xDSL IDSL Module. BERT transmission test for point-to-point and eoc loopback applications. CLEI: VATSHS0BAA CPR/OFC: 774315 See_Image SSxDSL-6 Module SunSet xDSL VF TIMS Module. CLEI: VATSJT0BAA CPR/OFC: 774316 See_Image SSxDSL-7 Module SunSet xDSL SDSL Module. Uses Conexant RS8973 chipset. CLEI: VATSSKY0BAA CPR: 774380 See_Image SSxDSL-8 Module SunSet xDSL Provides basic T1 loopback testing, Fractional T1, hitless full duplex drop and insert for talk/listen. See_Image SSxDSL-9 Module SunSet xDSL Datacom/DDS 4-wire Module. Provides DDS 4-wire local loop testing and Datacom testing for V.35, RS530, RS449, RS232, and X.21. Includes SS308 Datacom cable. Cables and adapters purchased separately. CLEI: VATSLZ0BAA CPR: 774381 See_Image SSxDSL-10 Module SunSet xDSL ADI ADSL ATU-R Module. CLEI: VATSDX0BAA CPR: 774379 See_Image SWxDSL-10A Software SunSet xDSL PING Package for SSxDSL-10. ICMP PING with ATM encapsulation to verify end-to-end provisioning See_Image SWxDSL-1T1 Software SunSet xDSL T1 Testing. Adds T1 test capabilities to the PairGain T1 HDSL Module (SSxDSL-1)See_Image SWxDSL-3A Software SunSet xDSL PING Package for SSxDSL-3. ICMP PING with ATM encapsulation to verify end-to-end provisioning. See_Image SWxDSL-5BRIE Software SunSet xDSL BRI Emulation: ETSI. Adds BRI call setup with ETSI Protocol to SSxDSL-5 IDSL Module See_Image SWxDSL-5BRIN Software SunSet xDSL BRI Emulation. Adds BRI call setup with North American Protocols to SSxDSL-5 IDSL Module See_Image SWxDSL-5BRIPA1 Software SunSet xDSL ISDN Protocol Analysis. IDSL D-channel protocol analysis for the SSxDSL-5 IDSL Module. Includes 1MB SRAM card. Requires SWxDSL-5BRIN or SWxDSL-5BRIE. See_Image SWxDSL-DDMM Software SunSet xDSL Delete DMM. Deletes DMM capability from SSxDSL Full Chassis (SSxDSL) See_Image SWxDSL-DLM Software SunSet xDSL Delete Line Measurements. Deletes Line Measurements from SSxDSL Full Chassis (SSxDSL) See_Image SWxDSL-DTDR Software SunSet xDSL Delete TDR. Deletes TDR capability from SSxDSL Full Chassis (SSxDSL) See_Image SWxDSL-L1 Software SunSet xDSL Load Coil Detector. Load Coil Detector feature for the SunSet xDSL Light Chassis (SSxDSL-L) See_Image ACCESSORIES These prices and information are from the manufacture and are listed as refference only. SSDCOM-DCC Adapter Package SunSet xDSL Datacom Adapters Package. Includes datacom adapters SS253, SS254, SS255, SS262B, and SS267 $ 350.00 SSDCOM-DCY Adapter Package SunSet xDSL Datacom Adapters Y Package. Includes datacom adapters SS253, SS253Y, SS254, SS254Y, SS255, SS255Y, SS262B, SS267, and SS267Y $ 700.00 SSxDSL-1M Manual SunSet xDSL Users Manual Insert for SSxDSL-1 PairGain T1 HDSL Module. More... $ 45.00 SSxDSL-10M Manual SunSet xDSL Users Manual Insert for SSxDSL-10 ADI ATU-R Module. More... $ 45.00 SSxDSL-3M Manual SunSet xDSL SSxDSL-3M, Users Manual Insert for SSxDSL-3 Alcatel ADSL ATU-R Module. More... $ 45.00 SSxDSL-4M Manual SunSet xDSL SSxDSL-4M, Users Manual Insert for SSxDSL-4 Alcatel ADSL ATU-C Module. More... $ 45.00 SSxDSL-5M Manual SunSet xDSL SSxDSL-5M, Users Manual Insert for SSxDSL-5 IDSL Module. More... $ 45.00 SSxDSL-6M Manual SunSet xDSL SSxDSL-6M, Users Manual Insert for SSxDSL-6 VF TIMS Module. More... $ 45.00 SSxDSL-7M Manual SunSet xDSL SSxDSL-7M, Users Manual Insert for SSxDSL-7 SDSL Module. More... $ 45.00 SSxDSL-9M Manual SunSet xDSL SSxDSL-9M, Users Manual Insert for SSxDSL-9 Datacom/DDS Module. More... $ 45.00 SW2504 Card SunSet ISDN, xDSL Dummy Card to protect the 2nd Memory card slot when empty. $ 25.00 SW2515 Software/Card SunSet ISDN 1 Mbyte SRAM memory card with battery back-up to increase the storage capacity of the test set. $ 345.00 SA251 Cable SunSet xDSL RJ45(m) 8 pin modular plug to 6 alligator clips, 3m See_Image $ 190.00 SA261 Cable SunSet xDSL, Intl RJ45(m) 8 pin modular plug to 2 small alligator clips with ferritte filter, 2m See_Image $ 60.00 SA681 Case SunSet xDSL Storage case for SunSet xDSL Plug-In Module $ 20.00 SA708 Cartridge SunSet xDSL, SDH 8Mb Replacement software Cartridge. Contact technical support for this item. $ 285.00 SA903 Training CD SunSet xDSL SunSet xDSL Training CD. Available at no charge with purchase of SunSet xDSL. $ 25.00 SS104D Cigarette Lighter Battery Charger SunLite E1, SunSet T10, T3, STS-1, OCx, ISDN, xDSL, Intl, E20, E10, E1e, SDH, PDH, SSxDSL-CTY-01 15.5V, 2.5A output. To be used with SunSets equipped with NimH batteries only See_Image $ 85.00 SS112 Cable SunSet T1, T3, T10, STS-1, OCx, ISDN, xDSL, Intl 2 single bantams to RJ48 8-position modular plug, 6 ft (2m) See_Image $ 60.00 SS115 Printer Cable SunLite E1, SunSet T1, T3, T10, STS-1, OCx, ISDN, xDSL, E1e, E10, E20 Printer Cable, DIN-8 to RS232C1m (DIN-8 to DB-25 RS232C). Replacement printer cable for earlier serial printers such as SS118. See_Image $ 20.00 SS115C Printer Cable SunSet T1, T3, T10, STS-1, ISDN, xDSL, OCx DIN-8 to 6-pin RJ-11 Printer Cable. Compatible with the STAR DP-8340 printer interface. See Image $ 20.00 SS115D Printer Cable SunLite E1, SunSet T3, STS-1, OCx, ISDN, E1e, E10, E20, SDH, PDH DIN-8 to DB-9 RS232C Included when either Remote Control or SS118B/C printer is ordered $ 20.00 SS117 Printer Paper SunLite BRI, E1, SunSet T3, T10, OCx, xDSL, STS-1, E10 Printer Paper, 5 rolls, for SS118B/C. See Image $ 45.00 SS118B Printer SunLite E1, SunSet T1, T10, T3, E10, STS1, ISDN, xDSL, OCx High Capacity Thermal Printer. With internal rechargeable battery. Includes cable (SS115B) for connection to SunSet and 110 VAC charger. See Image $ 475.00 SS118C Printer SunLite E1, SunSet T1, T10, T3, E10, STS1, ISDN, xDSL, OCx High Capacity Thermal Printer. With internal rechargeable battery. Includes cable (SS115B) for connection to SunSet and 220 VAC charger. See Image $ 475.00 SS118D Printer SunLite BRI, SunSet xDSL High Capacity Thermal Printer. With internal rechargeable battery. Includes printer cable (SS144) and 110 VAC charger. See Image $ 475.00 SS118E Printer SunLite BRI, SunSet xDSL High Capacity Thermal Printer. With internal rechargeable battery. Includes cable (SS144) for connection to SunLite and 220 VAC charger. See Image $ 475.00 SS122B Null Modem Adapter SunSet T3, xDSL, OCx Null Modem Adapter. DCE (f) to DCE (f), DB-9 conversion. See Image $ 25.00 SS122C Null Modem Adapter SunSet T3, xDSL Null Modem Adapter. DTE to DCE, DB-25 conversion. Replacement null modem adapter for earlier serial printers such as SS118. See Image $ 25.00 SS123A Jacket SunSet T1, T3, T10, OCx, ISDN, xDSL, SSE1, E20, E10, E1e, SDH, PDH SunSet Jacket. Provides additional weather protection for SunSets. $ 65.00 SS123B Carabiner Hook SunSet T1, T3, T10, OCx, ISDN, xDSL, SSE1, E20, E10, E1e, SDH, PDH For SunSet Jacket (SS123A) See_Image $ 10.00 SS138D Charger SunSet T3, OCx, xDSL SunSet AC Charger, 100 to 240 VAC, 50/60 Hz input, 15 VDC @ 2A output. For SS150B chassis only or SS150 chassis with NimH battery retrofit. See Image $ 120.00 SS140 Battery Pack SunSet STS1, ISDN, OCx, xDSL High Capacity NimH Battery Pack. 9-Cell, 10.8 VDC, 1.8 Ahr $ 200.00 SS143B SunSet Rubber Holster SunSet T1, T3, STS-1, OCx, ISDN, xDSL, Intl, E10, E8, E1e, SDH, PDH Protective rubber covering with integrated instrument stand. Not compatible with SS116 or SS123A. See_Image $ 55.00 SS144 Printer Cable SunLite BRI, SLE1, SunSet xDSL, Intl 6-pin RJ11 to DB-9 Included when SS118 D/E is ordered See_Image $ 20.00 SS144A Printer Cable SunLite BRI, E1, E1-MSN, SunSet xDSL, Intl 6-pin RJ11 to DB-25 Replacement printer cable for earlier serial printers such as SS118 See_Image $ 20.00 SS144B Printer Cable SunSet xDSL, Intl 6-pin RJ11 to 6-pin RJ11. Compatible with the STAR DP-8340 printer. See_Image $ 20.00 SS160 Manual SunSet xDSL SunSet xDSL Full Chassis User’s Manual $ 90.00 SS160-M Manual SunSet xDSL SunSet xDSL Module Chassis Users Manual $ 45.00 SS161 Cable SunSet xDSL, MTT, Intl Cable, RJ45(m) to 3 Probe Clips, 6 ft. See_Image $ 90.00 SS161-HPU Cable SunSet xDSL, Intl RJ-45 to 2 Retractable Banana and Ground Clip. Alligator Clips included. See_Image $ 90.00 SS162 Cable SunSet xDSL, Intl RJ45 (m) 8-pin Modular Plug to RJ14 6-pin Modular Plug, 2m. Used for SunSet to Alcatel splitter’s 6-position modem jack See_Image $ 35.00 SS163 Cable SunSet xDSL, Intl RJ45 (m) 8-pin Modular Plug to RJ45 (m) 8-pin Modular Plug, 2m. Used for SunSet to Alcatel splitter’s 8-position modem jack See_Image $ 35.00 SS164 Cable SunSet xDSL, Intl RJ11 (m) 6-pin Modular Plug to 2 Probe Clips, 2m. Used for network connection from external POTS splitter (SS165) See_Image $ 60.00 SS165 Splitter/Filter SunSet xDSL, Intl External POTS Splitter, low-pass filter. Provides access to POTS signal for ADSL applications. See Image $ 90.00 SS166 Cable SunSet xDSL, Intl 2 Single Bantams to RJ-45 8-pin Modular Plug, 2m. Used for HDSL port on the PairGain T1 HDSL Modem (SSxDSL-1) See_Image $ 60.00 SS167 Cable SunSet xDSL, Intl RJ45 (m) to RJ45 (m), 2m with Ferrite Filter See_Image $ 20.00 SS168 Cable SunSet xDSL, Intl RJ45 (m) to RJ11 (m), 2m with Ferrite Filter See_Image $ 20.00 SS252 Adapter SunSet T10 V.35 DTE (SS252T) and DCE (SS252C) Interface Adapters. DB37 to ISO 2593 34 pin connectors. See_Image $ 120.00 SS252C Adapter SunSet T10 V.35 DCE Interface Adapter. DB37 to ISO 2593 34 pin connectors. See_Image $ 60.00 SS252T Adapter SunSet T10 V.35 DCE Interface Adapter. DB37 to ISO 2593 34 pin connectors. See_Image $ 60.00 SS253 Adapter SunSet T10 X.21/V.11 DTE (SS253T) and DCE (SS253C) Interface Adapters. DB37 to ISO 4903 DB15 connectors. $ 70.00 SS253Y Cable SunSet E20, xDSL X.21/V.11 Datacom Monitor Y-cable DB37 to male and female to ISO 4903 DB15 connectors See_Image $ 90.00 SS254(C+T) Interface Adapter SunSet T10, xDSL , E10, E20 RS232/V.24 DTE (SS254T) and DCE (SS254C) Interface Adapters DB37 to ISO 2110 DB25 connectors See_Image $ 70.00 SS254Y Cable SunSet E20, xDSL DB37 to male and female ISO 2110 DB25 connectors See_Image $ 95.00 SS255(C+T) Adapter SunSet T10 RS449/V.36 DTE (SS255T) and DCE (SS255C) Interface Adapters. See_Image $ 70.00 SS255C Adapter SunSet T10 RS449/V.36 DCE Interface Adapter, DB37 to ISO 4902 DB37 connectors. See_Image $ 40.00 SS255T Adapter SunSet T10 RS449/V.36 DTE Interface Adapter, DB37 to ISO 4902 DB37 connectors. See_Image $ 40.00 SS255Y Cable SunSet xDSL, E20 RS449/V.36 Datacom Monitor Y-cable DB37 to male and female ISO 4902 DB37 connectors See_Image $ 105.00 SS262B Adapters SunSet T10, xDSL, Intl, E20, E10 RS530 DTE (SS262T-B) and DCE (SS262C-B) Interface Adapters. DB37 to ISO 2110 DB25 connectors. See_Image $ 80.00 SS267Y Adapter SunSet xDSL V.35 Datacom Monitor Y-cable. DB37 to male and female ISO 2593. 34 pin connectors $ 145.00 SS308 Cable SunSet T10, xDSL, Intl, E20 Datacom cable; SCSI-36 (m) to DB-37 (f) Interface cable, 2m See_Image $ 150.00 SS432-U Cable SunSet ISDN, SunLite BRI RJ 48 to RJ11, 2m see_image $ 20.00 SA903 Tape SunSet OCx SunSet xDSL Training CD, English. Available at no charge with purchase of a SunSet xDSL Full or Module chassis, when specified at time of order. $ 25 SS101 SunSet Carrying Case SunSet T1, T10, T3, STS-1, OCx, ISDN, xDSL, Intl, E20, E10, E8, E1e, SDH, PDH SunSet Carrying Case See_Image $ 85.00 Pay Pal Bid Pay Credit Card / e-Check Money Orders

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Type	Datacom & Telecom Measurement
Manufacturer	Sunrise Telecom