Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 0

Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 1

Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 2

Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 3

Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 4

Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 5

Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 6

Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 7

Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 8

Sweco FMD-4LR 4 foot vibratory deburring machine Vibro-Energy Finishing Mill, US $1,500.00 – Picture 9

Sweco Fmd-4lr 4 Foot Vibratory Deburring Machine Vibro-energy Finishing Mill

US $1,500.00

Spruce Pine, North Carolina, United States
Mar 11th

Open on mobile:
QR code

Sweco FMD-4LR 4 foot vibratory deburring machine - a Vibro-Energy Finishing Mill The chamber of the Finishing Mill is lined with 95 durometer state-of-the-art polyurethane. The polyurethane is hot-poured, hot-cured and degassed for maximum density. The chamber uses a ribbed outer wall design to prevent parts sticking. It is supplied with one 5" diameter quick-release media discharge door and one 3" diameter bottom drain with 1/8" diameter self-relieving holes. The drain terminates with a 1-1/2" OD spout for customer connection. The swing blade assembly is air-operated via an air switch, and is fabricated of cast polyurethane to prevent part damage. One screen assembly is included with the unit, available in 5/8", 7/8", 1", or 1-3/8" clear openings. The chamber is also equipped with COMPOUND FEED NOZZLES mounted around the center column, connected with tubing to a coupling on the outside of the mill base. DRIVE SYSTEM: SWECO Vibro-Energy Finishing Mills provide a unique three-dimensional vibratory motion of parts and media, insuring precisely controlled deburring and finishing. The Model FMD-4LR finishing chamber has an actual capacity of 4 cubic feet with a chamber diameter of 42 inches and a processing channel width/depth of 10 X 10 inches. The maximum part length is 18 inches and the maximum gross chamber load is 1200 pounds. The minimum lining thickness in high wear areas is 5/8 inch. The diameter of the machine is 42 inches, height is 48 inches and load/unload height is 40 inches. The approximate shipping weight is 1000 pounds. The Finishing Mill Chamber is mounted on twelve heavy-duty equally spaced spring assemblies. The spring assemblies are retained in place by the use of polyurethane spring spools, mounted to base top flange and chamber bottom. This design virtually eliminates spring failure and energy transmission to the floor. FINISHING CHAMBER: A 2-1/2 horsepower, 230 or 460 volt, 60 hertz, 1200 RPM, TENV, grease lubricated SWECO Motion Generator of double-end shaft design, with two end bell assemblies is used. Eccentric weights, which provide the vibration source,

“Works perfectly, Very nice liner.”