TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 0

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 1

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 2

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 3

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 4

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 5

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 6

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 7

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 8

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 9

TEKTRONIX 465B 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (Late Build), US $350.00 – Picture 10

Tektronix 465b 100 Mhz Analog 2-ch Inspected, Tested , Adjusted (late Build)

US $350.00

Milligan College, Tennessee, United States
Feb 24th

Open on mobile:
QR code

This Scope 465b ( Tektronix replacement for the older 465 model ) has been inspected for cold solder joints , damaged, out of spec, or missing components, etc. (replaced where required) All internal power supplies have been checked and adjusted for both voltage and ripple as per manual.( caps \ components replaced when required to make spec, see pictures) Both channels Volts \ Division have been calibrated 5mv>5v per division. "CAIG" Deoxit Gold 100% has been applied ( very expensive) to the Volts \ Division and DC-GND-AC switches. Both Channels have been adjusted (per Tektronix Spec) for "low" and "High" Frequency compensation, in addition to being checked with and "tweaked"with a "Tunnel Diode Pulser". Included with this scope is as follows: 1. Full Tektronix Maintenance Manual CD, Operators Manual with the missing pages, pictures diagrams waveforms and complete schematics. 2. 2 - New x1 x10 100Mhz Probes, 1 Tektronix 6122 100 Mhz x10 probe 3. A 42" calibration RG 58AU 50 Ohm cable ( as per Tektronix requirement) with NOS Kings BNC connectors ..The one that was used to adjust this scope, less the 50 Ohm load. 4. One set of "Custom Machined Tektronix replacement Cord-Wrap \ Feet " (see pic's) 5. This Scope has been run and cycled on my bench for weeks ( see pic's) I compare waveforms, levels, and functions against my other equipment. I do my best to insure that these units are working and are without problems. 6. Note: To obtain the waveforms and adjustments, The 42" RG 58AU 50 Ohm cable terminated into a 50 Ohm BNC load, or a Tektronix 6106A 250Mhz x10 probe was used. 7. If for some reason the scope arrives "DOA" ( being mishandled or dropped) I will issue a refund. ( buyer pays return shipping) Contact me with any questions or problems as it could be something simple. These units 465B's 475's use sockets for some or all of the "IC's and Xstr's" and can be "jarred loose " in the case of mishandling. Thanks for looking ...Regards Fred

Condition:	Seller refurbished: An item that has been restored to working order by the eBay seller or a third party not approved by the manufacturer. This means the item has been inspected, cleaned, and repaired to full working order and is in excellent condition. This item may or may not be in original packaging. See the seller’s listing for full details. ...	Brand	Tektronix
Bandwidth	100 Mhz
Model	465B
Channels	2
Type	Analog
Make	Tektronix