Vintage Lambda Regulated Power Supply Lt-1095am

US $200

Hayward, California, United States
May 24th

Open on mobile:
QR code

Up for your consideration / auction is an Vintage Lambda Power supply LT-1095AM regulated power supply. Please read this description and review and examine all the pictures before placing any bids on this item. I have had this power supply in my possession since 9-15-2000. I bought this for a project that I never did get around to doing. It has been inside of dry storage of an warehouse for the past 12 years, I have not used it. It is made in Huntington, NEW YORK from the back information plate lettering of silk screen printing that was done at the factory. This power supply is in nice condition. It has been lightly used, with only some scratch marks on the bottom from being moved around in it's storage days. There are a few scratches on the top left edge of the case from being handled and that is all of the marks on the other sides of this case that I could find. There is also some glue residue that is embedded into the paint on the middle part of the top cover. The front panel is in nice usable shape with all the hand tighten screw on terminals present and the Phillips-head screws are all in great shape with no rounding out of the heads of the screws. The power on indicator is present and looks to be in good shape. The Thermal Overload indicator is present and seems to be in good shape. Some of the case screws that are not stainless steel do have some surface rust on them The only thing I could find wrong is that are a few areas on the front face where the paint has worn away and the metal is slightly exposed and you can see this in the photos of the front face. All the sides of the casing seems to be in great shape with no major marks or dents, there is a few areas where the factory paint has come off and there are a small bit of surface rust on there areas, please see the photos.. The rear of the case has a terminal block and 120 Volt power cord installed. It looks to have been used lightly as there there is only a slight amount of dust. All the ventilation holes on the top, side, and bottom are all clear and clean and are not damaged in any way. There are no burn marks or heat damaged paint anywhere on this power supply. There are several sets of mounting holes on the front,side, and bottom of this power supply, made of course to mount it inside of a rack or other mounting equipment. This power supply is currently wired for 120 input Voltage operation and has a rear wire connection for the current/voltage output from this power supply. I was only able to test the voltage output of this power supply and that was found to be working properly. I was unable to fully/correctly test the current output of this power supply as I do not have a way to properly load test this power supply so this portion or part of it I will have to list it as not working or for parts only. Specifications of this Power supply LT-1095AM: 1 Nominal output Voltage V Adjustable by user, switch selection: 0-8 Volts, 8-16 Volts, 16-24 Volts, and 24-32 Volts. 2 Maximum Output Current 0-1.0 Amp DC Regulated Max Ambient 50 Degrees C (122 Degrees F) 3 Maximum Output Power Watts Unknown 4 Efficiency (Typ) % Unknown 5 Input Voltage Range 105 ~125 VAC; 50-400 Hz. 6 Input Current (Typ) N/A 7 Inrush Current(Typ) N/A 8 Output Voltage Range (Typ) % N/A 9 Maximum Ripple & Noise mV Unknown 10 Maximum Line Regulation Unknown 11 Maximum Load Regulation Unknown 12 Over Current Protection external overload protection: Overload light on front panel, Thermal overload breaker, reset switch on back panel. internal failure protection: provided by fuse #A-3AG "SLO-BLO" 13 Over Voltage Protection N/A 14 Hold-Up Time (Typ) N/A 15 Remote Sensing Unknown 16 Remote ON/OFF Control N/A 17 Parallel Operation Possible 18 Series Operation Possible 19 Operating Temperature Unknown 20 Operating Humidity N/A 21 Storage Temperature Unknown 22 Storage Humidity N/A 23 Cooling Convection cooled, no blowers, no external heat sinks. 24 Temperature Coefficient Unknown 25 Withstand Voltage Input - Chassis : N/A Input - Output : N/A Output - Chassis : N/A 26 Isolation Resistance N/A 27 Vibration N/A 28 Shock N/A 29 Safety Standard Completely protected. Short circuit proof; continuously adjustable automatic current limiting 30 Conducted Emission N/A 31 Weight Lbs 34 32 Size (WxHxD) inches 3-1/2 Height x 16 Deep including the front handle (14.5 w/o handle) x 17-1/4 wide (1/4 wide for screw not flush mounted on side of case). 33 Monitoring Signal N/A Features of this power supply: Designed for both bench and rack use. Convection cooled no blowers, no external heat sinks. Series/parallel operation Output voltage user adjustable Constant voltage/constant current Completely protected. Short circuit proof; continuously adjustable automatic current limiting Separate meters provide simultaneous monitoring of both voltage and current. I am available to answer questions in the early morning AMs from Monday through Friday. I do ship items, once they have been fully paid for, in the the very early afternoons on Mondays through Fridays. I do not ship items on weekends or holidays as the USPS is closed on those days. The power supply will be double boxed and shipped as if I was receiving it, an will be very well packaged. Insurance and Signature Confirmation is included in the shipping price of this power supply.