This is a model 760101-06-C1-D/C10 06 - six 5A Elements C1 - GPIB Interface C10 - SCSI, HDD Ethernet The unit was recently calibrated and comes with certificate of calibration from JJ Calibration LLC Simultaneous Measurement of 3 Phase Power from Two Systems Using One Unit Covers a Wide Voltage and Current Range Fast Data Storing Interval (50 ms) Fundamental Accuracy 0.1% Wide Frequency Bandwidth: DC, 0.5 Hz-1 MHz Integration Function Capable of Handling Rapid Changes in Input Signal Assured Accuracy with Small Currents within the Rated Range A Variety of Interfaces Broad Selection of Display Formats Such as Trend, Waveform and Vector Displays comes Standard with Harmonic Measurement Functions. Product Description: The WT1600 is power meter designed for measurement of extremely small currents in energy-saving equipment, as well as measurement of large currents for evaluating large-sized loads. The WT1600 works with voltages ranging from 1.5 V up to 1000 V, supporting a wide range of applications. Because it can accept signal inputs for up to six phases, a signal WT1600 unit can measure I/O signals on inverters. Features: Up to Six-Phase Input on One Units. Synchronized Measurenents Bet A single WT1600 unit can meke up to six different power measurements (six input each for voltage and current). With the measure start-stop function (synchronized measurement), two WT1600 units (12 inputs) can be synchronized. Wide Current Input Ranges The WT1600 has two different input elements. A 5 A input element is provided for measuring extremely small currents, while a 50 A input element serves to measure large currents. Both of the elements can be installed together in the WT1600. The current for the 5 A input element can be set as low as 10 mA for measuring extremely small currents in energy-saving equipment. Two input elements 5 A input element 10/20/50/100/200/500 mA, 1/2/5 A (DC, 0.5 Hz to 1 MHz) Current sensor input range (same for 5 A and 50 A input elements; standard) 50/100/250/500 mV, 1/2/5/10 V (DC, 0.5 Hz to 500 kHz) Data Storing as Fast as 50 ms (20 Times per Second) The data can be stored at intervals as short as 50 ms. The WT1600 rapidly calculates input parameters such as voltage rms, current rms, and power. Measurements can be stored in a 11-MB internal memory, which is helpful for applications such as: Evaluation of characteristics at motor startup including torque and rpms (requires the optional motor evaluation function) Measurement of rapidly fluctuating secondary voltage and lamp current when a light is turned on High Precision and Wide Bandwidth High Precision and Wide Bandwidth. The WT1600 has a higher measurement accuracy than any instrument in its class. It also features a 1 MHz measurement bandwidth (voltage, current) effective for such things as the evaluation of high-frequency illumination devices using inverters. Accuracy Characteristics for 5 A input Element (typical value) Accuracy Characteristics for External input (typical value) A Variety of Display Formats In addition to numerical data, the WT1600 can display input signal waveforms. Eleven different display formats can be selected on a single WT1600 unit, so it is not necessary to connect an external waveform viewer to check waveforms. The WT1600 displays measurements for each display updating interval in a time series. The time axis (T/div) can be set in the range of 3 seconds to 24 hours (wave off). Changes in up to 16 different parameters, such as voltage, current, active power, and apparent power, can be observed simultaneously in long-term continuous tests. Increased Assured-Accuracy Range For High-Precision Measurements Accuracy is assured at input ranges of 1% to 110% for AC, and 0% to 110% for DC. (However in the case of AC, it is necessary to input either a voltage or current that exceeds 10% relative to the range in order to have the voltage and current rms values calculated precisely.) Ethernet Port (10 BASE-T) and Internal Hard Drive (optional) The Ethernet function allow you to use FTP server, FTP client, Network printing, Automatic Mail Transfer (SMTP), and others. SCSI interface (optional) With the SCSI interface, you can save measured data to an external device such as an HDD. This is useful when you want to efficiently save measured data and image files. VGA output By connecting the VGA output signals to an external monitor, you can create large displays of numerical values and waveforms. Sold as is.
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
