2 muffler for sale, brand-new and used.

Product Description:Durable DuroMax 7.0 Hp, air cooled OHV engine with low oil shutoff . Heavy duty steel frame with four point fully isolated motor mounts for smooth and quiet operation. Full power panel with engine shutoff switch, volt meter, circuit breaker and power outlets.

I have a new old stock muffler for a 4.0 Onan Generator. Bought this from a old mechanic and it was stored in the attic of a old building. The body reads NELSON muffler embossed.

HIGH TEMP MUFFLER BLACK (600-1200 F) ~ SPECIALTY SILICONE BASED POWDER COATING FOR HIGH TEMPERATURE APPLICATIONS ~ THIS PRODUCT HAS A SLIGHT WRINKLE FINISH.

This Is an Exact Replica Ball Muffler For the 1 1/2 1 3/4 & 2 Hp Hercules, Economy, & Jaeger Hit & Miss Or Throttle Governed Gas Engines Using A 1" Pipe Thread For the Exhaust. This is 7" In Dia ..... 5 1/2 " tall 1 " Pipe thread......

This Is an Exact Replica Ball Muffler For the 1 & 1 1/2 Hp Sparta Economy Hit & Miss Gas Engines Using A 1" Pipe Thread For the Exhaust. This is very similar to the Ball Mufflers that were used on the various Early Hit & Miss Gas Engines This is 7" In Dia ..... 4 1/4 " tall 1 " Pipe thread......

This is a Rusty Ball Muffler For the Later Waterloo & Waterloo Contract Hit & Miss Gas Engines, All The Small H & K Waterloo Boy 1 1/2 1 3/4 with the 3/4" exhaust Used these Mufflers, As it shows them in the Sales books..... Fits: 1 1/2 1 3/4 & 2 Hp Sizes.. With 3/4" Exhaust Pipe I would say that if you Have any Waterloo Or Waterloo Contract Engine, That Uses A 3/4 Pipe thread this would be the correct style muffler for your Engine This is 6 1/2" In Dia

This is a New Replacement Ball Muffler For the Later Waterloo & Waterloo Contract Hit & Miss Gas Engines, All The Small H & K Waterloo Boy 1 1/2 1 3/4 with the 3/4" exhaust Used these Mufflers, As it shows them in the Sales books.....

This is a New Replacement Ball Muffler For Any Engine That Uses A 1 1/4" Pipe thread For the exhaust, It is Like Many Of The Mufflers That Were Made back Then & was used On Many Brands & Models Of Hit & Miss Gas Engines. This Is Bolted Together Like the Originals Were With 5/16" Square Nuts & Bolts, They were used On The Galloway, Associated, United, Witte, Amanco, 6 Hp John Deere, & Many Others, Basically anything with 1 1/4" Pipe thread Or Whatever You Can Adapt it to !!!!

When we set up to go to the show we are always thinking of something that we can hook to our engines so it will be turning something and make it extra special to look at. To me and I am sure you too, are think that the engine is pretty special and unique by itself. When tuned, these engines start easy and run great, but because of there design they smoke really good.

Here is a great muffler which fits many engines and looks great on any of them. This is a cast iron reproduction muffler. It is sand cast just as original and is fastened with un-plated square head 5/16" bolts.

This Is an Exact Replica Cone Style Muffler For the 1 1/2 1 3/4 & 2 Hp Economy, Jaeger, & Arco Hit & Miss Or Throttle Governed Gas Engines Using A 1" Pipe Thread For the Exhaust, I have seen this muffler Used on the later XI & XK, JI & JK Economy Engines. This is 6" In Dia ..... 3 " tall 1 " Pipe thread......