3 8 router bit for sale, brand-new and used.

This is a brand new, never used 3/4" cutting diameter straight router bit with two carbide flutes (blades) and a special gullet between cutting edges that allows for material clearing in mortising applications. The geometry of the blades and the open space between them is designed to allow for clean edge and clear bottom mortising up to about 3/8" depth for shallow hinges.

This is a brand new, never used 5/8" cutting diameter straight router bit with two carbide flutes (blades) and a special gullet between cutting edges that allows for material clearing in mortising applications. The geometry of the blades and the open space between them is designed to allow for clean edge and clear bottom mortising up to about 3/8" depth for shallow hinges.

This is a brand new, never used 5/32" radius roman ogee detail router bit with 1/2" shank. Overall diameter is 1-1/16" (11/32" cutting depth) with a 3/8" inch bearing and 2 carbide cutting edges (blades). Roman ogee and other edge detailing profiles are commonly seen on trim edges, and in wood furniture and are produced by running this bit along an edge while the bearing guides the router leaving a detailed edge.

Brand new, never used 3/8" key hole hanger router bit with 2 carbide cutting flutes and a 1/2" shank. Serves for plunge cutting a 3/8" hole to a desired depth at which point the router is slid laterally allowing the bit to cut a 1/4" slot along the top surface while maintaining a 3/8" cleared channel below.

AmericasPro.Tools Read feedback comments

Brand new, never used 3/8" diameter cove box router bit with carbide cutting edges and 1/2" shank. These bits are used to make half round coves of varying diameters up to a depth equal to the diameter of the bit leaving a long channel as in round fluted trim. Bit fits all 1/2" shank portable and table routers.

Brand new, never used 3/8" flush trim panel pilot router bit with 1 carbide flute and a 1/2" shank. Serves for plunge cutting through a panel usually to make a guided cut against a template or rough framing from the other side. These bits most often see use in cutting larger sink openings in already installed counter tops or where a laminate is placed over an existing sink opening in the counter base material.

Description: 10pcs Titanium Coated Carbide PCB Engraving CNC Bit Router Tools 10 Degree 0.5mm Product Name: PCB engraving bit (carbide engraving bit Plating titanium) Carbide rods and tungsten steel rods, with high hardness, high wear resistance, high strength, resistance to bending, anti-impairment and long tool life.

Brand new, never used 3/8" round-over bit with 1/2" shank. Fits all 1/2" shank portable and table routers. C2 Micrograin tungsten carbide cutting edge provides a good balance of strength and durability.

This is a brand new, never used 3/8" cutting diameter flush trim straight router bit with a 3/8 inch bearing and two carbide flutes. Flush cut bits are used primarily for flush cutting edges to a template, guide or jig. The bearing at the end is of the same diameter as that of the cutting depth so that the cutters will clear all material outside any template the bearing rolls along.

This is a brand new, never used 3/8" cutting diameter flush trim straight router bit with a 3/8 inch bearing and three carbide flutes or blades for superior smoothness, speed, and consistency of cut. Flush cut bits are used primarily for flush cutting edges to a template, guide or jig. The bearing at the end is of the same diameter as that of the cutting depth so that the cutters will clear all material outside any template the bearing rolls along.

This is a brand new, never used 1/2" cutting diameter straight router bit with two carbide flutes (blades) and a special gullet between cutting edges that allows for material clearing in mortising applications. The geometry of the blades and the open space between them is designed to allow for clean edge and clear bottom mortising up to about 3/8" depth for shallow hinges.

This is a brand new, never used 3/8" cutting diameter straight router bit with two carbide flutes or blades. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or an added shank bearing, for flush cutting edges to a template. This bit fits all 1/2" shank portable and table routers.

This is a brand new, never used 5/8" cutting diameter straight router bit with three carbide flutes or blades for superior smoothness, speed, and consistency of cut. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or an added shank bearing, for flush cutting slab edges to a template. This bit fits all 1/2" shank portable and table routers.

Brand new, never used 10 degree dovetail router bit with 3/8" cutting diameter at the widest point, carbide edges and 1/2" shank. These bits are used for woodworking joinery along with a jig, or guide. The tapered dovetail shape makes alternating passes through one panel and opposite passes through another allowing for both straight end to end joining as well as right angle joints.

Hello and thank you for looking at my item(s)... For sale is a 3/8 in. Rabbit cut router bit.

9 - Milwaukee carbide router & laminate trimmer bits 1/4” shank all bits are made in USA. See photos for details.

a.im

var itemNumber = window.ebayItemID ?

5pc 1/2" Carbide ROUTER MOLDING BIT SET with Wood Case  Professional Quality  Tungsten Carbide Steel Router Bits