Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 0

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 1

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 2

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 3

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 4

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 5

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 6

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 7

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 8

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 9

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 10

Brandt KD79 2/CF Optimat 13mm Edgebander, 2001, 230V, PLC, Corner Rounding, US $17,940.00 – Picture 11

Brandt Kd79 2/cf Optimat 13mm Edgebander, 2001, 230v, Plc, Corner Rounding

US $17,940.00

Sheboygan, Wisconsin, United States
Jan 30th

Open on mobile:
QR code

Needs new controller & card (Stiles estimate - Approx. $12,500) Otherwise very good condition, cleaned well. Excellent parts machine; has two glue pots valued at $4,000 alone. Parts can be removed for buyer, but machine must be sold whole. Approx. replacement cost of this bander new is $90K USED BRANDT ( OPTIMAT KD79-2CF ) 13mm EDGEBANDER Edge cap: 0.4 - 13mm (1/2") Panel thickness 5/16" - 1-9/16" Min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width Line control (NO limit switches) for workstation function Equipped with:(2) 3 HP - 12,000 RPM Vertical Pre-milling/jointing heads "Quick change" glue tank for maintenance & glue color changeReversible rotation glue roller w/infrared heat zone to follow. Automatic magazine for strip & coil Large coil table 800 mm diameter to accommodate large coils of 3 mm PVC Stock 3 mm PVC guillotine (1) drive plus (3) idle roll "pneumatically controlled" pressure sections. Workstations: Double motor end trim (1/3 HP - 12,000 RPM motors) PLC controlled chamfer from 0° - 15° Top & bottom flush/radius trim, 0° - 45° bevel; (1/2 HP - 12,000 RPM motor), with insert knives for 3 mm PVC Radius 2-position control through PLC.2-Motor corner rounding unit for top & bottom corners (0.5 HP - 12,000 RPM motors) Top & bottom scraping for 2 - 6 mm radius, pneumatically controlled blowoff nozzles Top & bottom buffing (0.25 HP - 1,400 RPM motors). End trim & flush trim stations have HF motors w/electronic brakesfeed chain track speed 42 FPM 2 HP feed drive Pneumatic Exclusion/Inclusion on all major stations. Ask for pricing setup and demonstrated in our showroom Thoroughly Cleaned, partially checked, Needs a new controller and com card - BRANDT KD-79 2/CF Optimat Automatic Edgebander (2001) Automatic height adjustment with top pressure beam for all work stations. Equipped with digital height indicator. PC-16 Program Control: • Passive matrix Color LCD screen, 7.4”, VGA standard resolution of 640 x 480. • 8 mb IDE Flash Disc 100 mhz 486 DX4 Hard Drive • 8 mb RAM • Internal Modem for remote diagnostic link. Signal light at infeed to insure proper spacing of panels Extended Infeed Fence. Joint trimming / Pre-milling unit for pre-trimming the workpiece edges. Quickmelt granulate glue application system with approximately twelve minute heat-up time. Quick-change glue tank for easy maintenance and glue color change, if necessary. Reversible rotation of glue application roller. Retractable glue roller. Strengthened precutter for cutting PVC (max. 3 x 45 mm) from the coil. Infrared radiant quartz heating unit between glue roller and pressure zone for optimum gluing strength. Four roller pressure zone. End trimming unit with straight and chamfer capability. Chamfer up to 15degrees. Pneumatic indexing via program control. Fine trimming unit #1with digital “Quickset” system. Tilt range 0 - 25degrees. Pneumatic indexing via program control. Fine trimming unit #2 with digital “Quickset “ system. Tilt range 0 – 25 . Contour trimming unit for profile corner trimming. Sound enclosure with centralized dust extraction outlet. Scraping unit for rigid PVC edges. Buffing unit. Electronic frequency changer for all trimming motors which also incorporates electronic motor brakes. Must ship flatbed freight due to value and length Email or call 1-800-793-4494 if interested in this machine. Many other new and used machines are stored in our warehouse and can be viewed. Shipping & Freight: Purchaser/Buyer/Winning Bidder pays all shipping/freight costs associated with getting this machine to your location if item is to be shipped and not picked up in person. DELIVERY: Varies upon warehouse workload and potentially the item. This item may be released immediately by the warehouse, but sometimes up to 7 business days are needed to prep and release said item. Subject to Prior Sale. This item may be withdrawn from sale at any time as it is listed on our website and in other advertising. PAYMENT TERMS: Full Payment or deposit required within 24 hours of order, NO EXCEPTIONS. Items not paid for or held via deposit after 7 days will immediately be reported to eBay as unpaid! Cash in person, M.O., Personal/Company Check or Visa/Mastercard/Discover accepted. Wisconsin Sales and Use tax of 5% required for all purchases by Wisconsin residents who do not have a tax ID or are not able to fill out an exemption claiming the machine for business/manufacturing use. Minimum $125.00 Crating Fee, if required. Used equipment is sold as is, where is, unless otherwise specified. SELLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Freight, rigging, and installation are not included unless otherwise specified, but arrangements can be made at an additional cost.

Condition:	Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections. ...	Brand	Brandt
Model	770C