fairbanks cart for sale, brand-new and used.

Here we have a good heavy duty platform utility cart. I do not know the exact capacity, but it is at least a 2800lbs cart. It is very heavily built and is steel bound with an oak platform.

Jerome Industries p/n ILTF-10, Transformer 120vac to 12.5vac, 15 va (watts) 1.2A Dimensions (approximate): Length: 3.25 inches Width: 2.75 inches Height (including rubber feet): 2.35 inches Input and output Cords are both approximately 6 foot long. Weight (unit only, not shipping weight): 1 pound 6.7 ounces Combined Shipping - (When purchasing multiple items, you must use the ebay Shopping Cart, to be eligible for combined shipping.) 1.

RF Coaxial Plug SMB Straight Solder - Amphenol part number 27-1 This connector is New Old Stock, in the Original Packaging (a small plastic pill bottle). Note: the bottle has a crack, and some of the printing is worn off. See photos.

used 3P3T Rotary Switch, 3 position, 1/4 inch shaft, 3/8" mount bushing Solder terminals. Manufacturer unknown. Mounting hole: 3/8 inch diameter.

111SD, used 4P3T (or 4P5T) Rotary Switch, 3 or 5 position, 1/8" shaft, 1/4" mount bushing There are two rotation stop tabs. As presently configured, the 3 position stop tab is in place (and the 5 position stop tab is bent out of the way). To reconfigure for 5 positions: bend the 3 position tab out of the way, and bend the 5 position tab down (toward the wafters).

Fairbanks Morse Z52 3HP 3HP Engine has been repainted, condenser/radiator has no leaks, starts easily on magneto, and has no cracks or welds that I know of. New rings about 30 minutes run time on them, valves and seats touched up. Cart goes with it.

PA1007, used 3P3T Rotary Switch, 3 position, 1/4 inch shaft, 3/8" mount bushing Solder terminals Manufacturer unknown. Mounting hole: 3/8 inch diameter. Threaded bushing is 3/8 inch long.

used but original condition un molested. fairbanks brand hand truck . numbers stamped on side : 9272-1s.

AlcoSwitch MTA-306D 3PDT On-On Toggle Switch Solder terminals Ratings: 3A @ 250vac, 6A @ 125vac New old stock, sealed in bag. Combined Shipping - For quantities of any individual listed item, postage will be automatically calculated by ebay (based on your choice of shipping method, and the weight of the item (or lot), multiplied by the quantity ordered). For multiple separately listed items (sold by Wren's Electronic Supply), order the first item, but do not pay immediately.

Probe Master PM1025 Line Load / Termination Specifications: 75 ohm, 1 watt Connections: BNC Male & Female Shipping costs can be combined for multiple purchases. Please contact us if you have questions. Combined Shipping - For quantities of any individual listed item, postage will be automatically calculated by ebay (based on your choice of shipping method, and the weight of the item (or lot), multiplied by the quantity ordered).

used 1P3T Rotary Switch, 3 position, 1/4 inch shaft, 3/8" mount bushing Solder terminals. Wafer material: ceramic. As presently configured, the outer wafer serves only as a terminal block for two 20K 2 watt resistors and one 610 ohm 1/2 watt resistor.

This is an Old Briggs & Stratton Gas Engine. Model R2 and Serial 2162. Good Compression and Spark.

This is a set of (4) ANTIQUE CAST IRON "THE FAIRBANKS CO" CASTER CART WHEELS ~ (2) SWIVEL. EMBOSSED 4M - 4". All wheels turn freely.

Amphenol 26-4502-24S, 24 pin Female Connector, with heavy duty locking hood This used connector is in very good condition. The outside of the shell has some minor corrosion. The inside of the shell and the connector contacts are corrosion free.

2 carts 30" x 54" 1 cart 30" x 60" 1 Jack (puller) Good condition 1000 lb capacity Local Pick Up only Cash Only

26" Long Flexible Right Angle Drill Extension, holds standard bits to 1/4" Shaft I am the original owner of this tool. It was used in aviation maintenance work on light aircraft. This tool has no markings to indicate manufacturer, model, etc.

Vintage 10.5" Heavy Natural Rubber Bungee Cords with bolt eyes Markings on rubber: General, A841A, #9 Dimensions (approximate): Overall: 10.5 inches Rubber length: 9 5/16 inches Rubber cord diameter: 1/2 inch Eye: outside diameter 1/2 inch, inside diameter slightly less than 5/16 inch (will easily accept a 1/4" bolt) These are New Old Stock. The rubber does not show any signs of cracking or deterioration. The bolt eyes are steel.

2 Equipment Case Enclosure Black Plastic Handles, 5 3/16" x 1-3/16"- some damage These handles are made of tough slightly flexible plastic. One is ready to go, as is. The other might be usable for light duty, with some TLC.

PA300, used 5P3T Rotary Switch, 3 position, 1/4 inch shaft, 3/8" mount bushing Solder terminals. Wafer material: ceramic. Manufacturer unknown.

Fairbanks model 9292-HC (Ref. Grainger 18F478 for item specifics) 30 - 55 gallon 1000 pound capacity barrel or drum hand cart. Very well made heavy duty all welded construction with two 10" X 2-1/2" rubber over solid cast steel wheels with ball bearings and grease fittings and it has a kick stand for holding or storing it upright.