Fg-100 Dds Function Signal Generator Module Good Accuracy Frequency Counter

US $26.59

Monroe Township, New Jersey, United States
Sep 4th

Open on mobile:
QR code

Home Electronic Component Chips Sensor Arduino Module Raspberry Pi FG-100 DDS Function Signal Generator Module Good Accuracy Frequency Counter Popular Popular Product Introduction Description Pattern Name: 1HZ-500KHZ Used for alignment of audio equipment and up into the lower radio frequencies at the lower end of the Am band or Amateur bands Features: Small size, complete functions, simple operation, easy to carry. It can be powered by adapter or lithium battery. The good accuracy and frequency stability of DDS are suitable for oscilloscope scanning time factor calibration. Square wave output, suitable for oscilloscope attenuator and probe pulse characteristic adjustment. Together with the oscilloscope, it can be used for electronic circuit test and debugging, frequency characteristics and impulse response test and measurement of audio amplifiers. Technical index: 1. Frequency range: sine wave 1Hz-500kHz (where the output amplitude is flat to 200 kHz, the output amplitude will decrease as the frequency is further increased), other waveforms 1Hz-50kHz (but the upper limit of the adjustable frequency is not limited, if The requirements for distortion and shaking are not high, and the frequency of use can be further increased). 2. Resolution: 1Hz. 3. Output waveform: sine wave, square wave, triangle wave, forward sawtooth wave, reverse sawtooth wave, electrocardiogram, noise wave. 4. Sine wave distortion: <1% below 1kHz, <0.5% above 1kHz. 5. Output amplitude: maximum ±10V (P-P). 6. Output impedance: 50 ohms. 7. DC offset: maximum ±10V, with shutdown function. 8. All setting parameters can be saved 9. There are filters that can be turned on and off, which can be well adapted to the output of sine and pulse waveforms. 10. Power supply: DC3.7-10V. It is recommended to use DC5V adapter, or 3.7V lithium battery. 11. Dimensions: 140x80x27 mm Package Included: 1 x DDS Function Signal Generator 1 x USB to DC Power Cable Payment Shipping Refund Payment We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right. Payment must be received in 5 business days of auction closing. Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. Shipping We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. Refund All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund. If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item. Home Electronic Component Chips Sensor Arduino Module Raspberry Pi FG-100 DDS Function Signal Generator Module Good Accuracy Frequency Counter Product Introduction Description Pattern Name: 1HZ-500KHZ Used for alignment of audio equipment and up into the lower radio frequencies at the lower end of the Am band or Amateur bands Features: Small size, complete functions, simple operation, easy to carry. It can be powered by adapter or lithium battery. The good accuracy and frequency stability of DDS are suitable for oscilloscope scanning time factor calibration. Square wave output, suitable for oscilloscope attenuator and probe pulse characteristic adjustment. Together with the oscilloscope, it can be used for electronic circuit test and debugging, frequency characteristics and impulse response test and measurement of audio amplifiers. Technical index: 1. Frequency range: sine wave 1Hz-500kHz (where the output amplitude is flat to 200 kHz, the output amplitude will decrease as the frequency is further increased), other waveforms 1Hz-50kHz (but the upper limit of the adjustable frequency is not limited, if The requirements for distortion and shaking are not high, and the frequency of use can be further increased). 2. Resolution: 1Hz. 3. Output waveform: sine wave, square wave, triangle wave, forward sawtooth wave, reverse sawtooth wave, electrocardiogram, noise wave. 4. Sine wave distortion: <1% below 1kHz, <0.5% above 1kHz. 5. Output amplitude: maximum ±10V (P-P). 6. Output impedance: 50 ohms. 7. DC offset: maximum ±10V, with shutdown function. 8. All setting parameters can be saved 9. There are filters that can be turned on and off, which can be well adapted to the output of sine and pulse waveforms. 10. Power supply: DC3.7-10V. It is recommended to use DC5V adapter, or 3.7V lithium battery. 11. Dimensions: 140x80x27 mm Package Included: 1 x DDS Function Signal Generator 1 x USB to DC Power Cable Payment Shipping Refund Payment We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right. Payment must be received in 5 business days of auction closing. Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. Shipping We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. Refund All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund. If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	Unbranded
UPC	Does not apply
MPN	Does not apply
EAN	Does not apply
Country/Region of Manufacture	China