1931F6E.1.64 New WCB Flow Products (a Division of SPX Process Equipment), 2" High Pressure Sanitary Clamps, Part Number 119-271, Series 13MHP. Each bid quantity is for One (1) Clamp. You may bid / buy any number, up to the total quantity available above.
Lot of top of the line Hilti brand 387509 3/8-16 X 3" long zinc concrete wedge anchors. These are brand new KB-TZ anchors taken from the original sealed box, you will receive a total of (36) anchors and matching nuts and washers are included. I will carefully re-package these into a small flat rate box to save on shipping cost's and ship them promptly.
Lot of Wej-it brand H3450 3/4-10 X 5" long zinc concrete or masonry wedge anchors. These are brand new anchors in their original box that came from a local hardware store that closed. You will receive a total of (7) anchors and matching nuts and washers are included.
Lot of Wej-it brand H5842 5/8-11 X 4-1/2" long zinc concrete or masonry wedge anchors. These are brand new anchors in their original box that came from a local hardware store that closed. You will receive a total of (8) anchors and matching nuts and washers are included.
Lot of Wej-it brand H5832 5/8-11 X 3-1/2" long zinc concrete or masonry wedge anchors. These are brand new anchors in their original box that came from a local hardware store that closed. You will receive a total of (8) anchors and matching nuts and washers are included.
Lot of Wej-it brand H1250 1/2-13 X 5" long zinc concrete or masonry wedge anchors. These are brand new anchors in their original box that came from a local hardware store that closed. You will receive a total of (10) anchors and matching nuts and washers are included.
Lot of Wej-it brand H3850 3/8-16 X 5" long zinc concrete or masonry wedge anchors. These are brand new anchors in their original box that came from a local hardware store that closed. You will receive a total of (20) anchors and matching nuts and washers are included.
Lot of Wej-it brand H3823 3/8-16 X 2-3/4" long zinc concrete or masonry wedge anchors. These are brand new anchors in their original box that came from a local hardware store that closed. You will receive a total of (19) anchors and matching nuts and washers are included.
Lot of Powers power-stud brand 1/2-13 X 7" long zinc concrete or masonry wedge anchors. These are brand new anchors that came from the bulk bins of a local hardware store that closed. You will receive a total of (20) anchors and matching nuts and washers are included.
Lot of Powers power-stud brand 1/2-13 X 8-1/2" long zinc concrete or masonry wedge anchors. These are brand new anchors that came from the bulk bins of a local hardware store that closed. You will receive a total of (25) anchors and matching nuts and washers are included.
Lot of Powers power-stud brand 3/4-10 X 4-3/4" long zinc concrete or masonry wedge anchors. These are brand new anchors that came from the bulk bins of a local hardware store that closed. You will receive a total of (10) anchors and matching nuts and washers are included.
Lot of Powers power-stud brand 5/8-11 X 5" long zinc concrete or masonry wedge anchors. These are brand new anchors that came from the bulk bins of a local hardware store that closed. You will receive a total of (10) anchors and matching nuts and washers are included.
B87C Features: A "partial throttle" type throttle valve allows a light blow for starting the tool. Improved, powerful, short-throw, face contact valve is virtually unaffected by wear. Valve Chest is reached easily by removing two short side rod bolts and backhead.
This listing is for an older Chicago Pneumatic CP 734 Air Wrench impact gun. This unit is used heavily and was disassembled because it would not remove car lug nuts but turned easily and didn't just hiss air out. All bearings are solid, hammer pins are within spec, no rust inside unit.
B87C Features: A "partial throttle" type throttle valve allows a light blow for starting the tool. Improved, powerful, short-throw, face contact valve is virtually unaffected by wear. Valve Chest is reached easily by removing two short side rod bolts and backhead.
New 1 set 'Helix' chuck adapter, from SDS drill chuck change to 1/2 inch drill chuck. When you install this adapter, the SDS hammer drill can use up to 1/2" straight shank products. Very useful tools.
IMPACT DRIVER VESSEL MADE IN JAPAN FEATURES: * LOOSENS OVERTIGHT, RUSTED OR 'FROZEN' SCREWS OR NUTS BY IMPACT WITH HAMMER * EASY ADJUSTMENT FOR FORWARD OR REVERSE * CONTAINS 4 BITS 36mm LONG. [PHILLIP #2 & #3. SLOTTED 8mm (5/16") & 10mm (3/8")] * REMOVABLE BIT HOLDER GIVES ACCESS TO 1/2 DRIVE FOR IMPACT
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.