internal threaded rod for sale, brand-new and used.

New billet aluminum replacement rear clamp block for your Delta Unisaw fence This is a replacement clamp block for the rear of the early style Unisaw fence. The early style fence is shown in photo #2. This fence is identified by the presence of the small rear clamp tighening knob above the lever lock at the operator side

Critikon Dinamap vital signs monitor 1846 This is a device (made by Critikon of Tampa, FL., USA) for measuring blood pressure and pulse rate. On the front of the device are: four digital di

New-in box Tiberlinx 4.75" Pipe Half Connectors with Pins Part# A475 Lot is for a box of 40. One slot with 7/8" internal thread at other end Overall length 4-3/4" Pin hole center from end of timber =3-7/8" (when connecting post to concrete and post to steel) Pin hole center to center = 7-7/8" + exposed threaded rod (when you use two A475's + threaded rod to customize your own TIMBERLINX)

TOTALLY REFURBISHED VINTAGE DELTA UNISAW FENCE. This is an early Delta table saw fence that fits all UNISAW's with the 1.375" diameter rails. This is the premium Delta Unisaw fence, with the cam locking ball ended lever and the knurled finger knob for tightening the rear clamp block.

BRAND NEW Dremel 506CU 7/8" Premium Metal Cutting Wheel The 506CU cutting wheel features a super abrasive grit called cubic boron nitride or CBN. CBN used on a cut-off wheel allows the wheel to remain sharp longer, stay cool, and it won’t shrink. The 506CU cutting wheel lasts at least 20 times longer than our fiberglass-reinforced cutting wheels based on internal testing.

Enerpac RCS-502 Single-Acting Aluminum Hydraulic Cylinder with 50-Ton Capacity, Single Air Port, 2.38" Stroke

This is a brand new, much improved, finger knob for the tightening the rear clamp on your vintage UNISAW fence. This is a easy-to-install replacement knob for tightening the rear clamp's J-hook found on the early style Delta

New "Saturn" ball knob for the locking lever on your Delta Unisaw fence. THIS AUCTION IS FOR THE KNOB ONLY. SEE MY OTHER AUCTION FOR THE KNOB AND THE STAINLESS STEEL SHAFT.

A NEW "Saturn" ball knob and stainless steel threaded shaft for the locking lever on your Delta Unisaw fence. THIS AUCTION IS BOTH THE KNOB AND THE SS SHAFT. IF YOU WANT ONLY THE KNOB, SEE MY OTHER AUCTION SITE.

American Educational 7-G15-A Cast Iron Support Ring Stand with Acid Resistant Finish, 8" Length x 5" Width Base Size *** FAST SHIPPING! ***

We have eight (8) new surplus Anaheim Automation Linear Step Motor Actuators Model # 23A104A. All eight are offered together for one bid of $150.00 These are rated on their labels as 5.0VDC, 1.0A 75lbs. These are a bit different from most traditional stepper motors in that they have an internal bronze acme threaded nut that turns with the stepper motor armature so that the threaded rod does not spin but moves in a linear fashion back and forth through the motor as it turns.

Wilton 350 vice that needs repair on rear of vise on main body and end cap has a piece broken off. Some welding repair could bring it back to life I suppose. Vise closes just fine however with end cap in current condition the vise pushes the end cap and threaded rod back and does not open the jaws as it should, you have to physically pull it open, it is old so all internal parts need to be cleaned and re-lubed.

Enerpac RCS-1002 Single-Acting Low-Height Hydraulic Cylinder with 100 Ton Capacity, Single Port, 2.25" Stroke Length

THE TEST SET OFFERS FLEXIBILITY TO MACHINING AND INSPECTION APPLICATIONS. EST SET CONSISTS OF THE FOLLOWING --- JEWELED INDICATOR CLAMP WITH 1-1/4" CAPACITY AND 1/4-28 THREADED HOLE FOR HOLDING ROD HOLE ATTACHMENT USED FOR CHECKING INTERNAL SURFACES OR THOSE NOT EASILY REACHED BY DIAL SPINDLE.. 375" DIA MOUNTING HOLE.