j clamp for sale, brand-new and used.

Package of two (2) Clamp-Rite 12810CR x ref. Destaco 381

Package of four (4) Clamp-Rite 12710CR x ref. Destaco 371

Package of four (4) Clamp-Rite 12510CR x ref. Destaco 351 12510CR 375lb j-hook flanged base latch clamp x ref. Destaco 351

PowerTec 20308 Hook Type of J Hook Toggle Clamp, 375 lbs Capacity Number-351

Fujikura New model Fusion Splicer

Fujikura New model Fusion Splicer

RARE STEEL 90-DEGREE CLAMP / ELBOW CLAMP MACHINIST TOOL CLAMPS 1/4" DIA PIPE/TUBING/HOSE/CABLE/TOOL/PART Used and in very good condition. Rare Steel 90-Degree Clamp for clamping 1/4" dia pipe / tubing / hose / cable / part / machine tool. And once clamped, you can secure this machine clamp tool using a bolt, cable or rope through the small 3/16" dia thru-hole, or secure the clamp into a vise or bigger clamp.

ANTIQUE VALVE STEM SEAT CUTTER JIG, 3V-1A VERSATILE TOOL HOLDER CLAMP STEEL VISE FILE HOLDER / ROD HOLDER / SHAFT HOLDER PIPE HOLDER / TUBE HOLDER JIG, 3V-1A HANDTOOL Used and in very good condition. This antique tool was originally made as a Valve Stem Seat Cutter, Model 3V-1A (make unknown). It is also a very Versatile Steel Vise / Clamp Tool Holder / File Holder / Rod Holder / Tube Holder / Pipe Holder / Shaft Holder Jig Handtool.

VINTAGE 4" J.H. WILLIAMS 404S DEEP THROAT CLAMP MADE IN U.S.A. Very nice old C-Clamp, Looks like someone got a little close to the clamp with a torch or welder (Please view last picture), Pictures considered part of description, Please view all pictures!

This is a J. H. Williams and Co.

VERSATILE 9" DRILL PRESS LOCKING CLAMP TOOL New old stock (NOS). Versatile 9" Drill Press Locking Clamp Tool / Hold Down Tool, Steel. Many uses beyond just drill presses, because this rugged drill press clamp can be bolted onto any sturdy plate, board or sheet 1-1/8" thick or less.

12" STEEL MACHINIST BLOCK / MACHINIST PLATE TOOL CLAMP PLATE: DISPLAYING, MACHINING, PAINTING, DRYING New old stock (NOS). 12" diameter sturdy Steel Machinist Block / Machinist Plate Clamp Tool Plate for displaying, machining, crafting, painting, and drying objects. Drilled holes are 1/4" diameter, and in a critically important radial pattern from the center, with a center hole.

Nice Williams No.2 Vulcan Heavy Service Clamp Used but in good condition. Opens to 2-1/4" and 2-1/2" deep. Bolt works smoothly.

This is a brand new, much improved, finger knob for the tightening the rear clamp on your vintage UNISAW fence. This is a easy-to-install replacement knob for tightening the rear clamp's J-hook found on the early style Delta

Is your Delta Unisaw Jet-Lock fence not "locking" the rear clamp like it should? It could be due to a damaged lever in the rear clamp casting. This part is an exact replacement for the original equipment cam lever that is located inside the casting at the rear of the rip fence.

(1) INTERNAL PIPE CLAMP TOOL, STEEL, 1" OD COMPRESSION CLAMP, COLLET MACHINIST TOOL Used and in very good condition, some scratch marks; works great. Steel Internal Pipe Clamp Tool, 1" OD, Machinist Tool Collet. This sale is for one (1) internal pipe clamp tool.

(1) RARE SPECIALTY CLAMP TOOL / BASKET CLAMP, STEEL, 10" Used and in very good condition. Rare Specialty Clamp / Basket Clamp Tool, steel, 10" long. The clamp tines close and open by moving the circular steel disk that the tines go thru forward or backward.

Two J.H. Williams Heavy Service Clamp, Vulcan CC-10. These clamps are in very good condition.