johnson furnace for sale, brand-new and used.

Johnson Gas Model 900SS Crucible Melting Furnace with Model 1207 Blower Console.Very Good Condition. Please see pictures for exceptional condition of Fire Brick, etc.This unit has very little use. Information & SpecificationsFurnace+Console Weight: 430lbs Voltage: 110Gas Connection: 1"Output: 240,000 BTU

Johnson gas furnace with blower, regulator, thermocouple and temperature gauge. 180,000 BTU/ HR. Serial number 1534-T.

This is a Johnson natural gas heat treat furnace #142-5. Includes a console unit and other attachments. Furnace Information:

Estate find, this Johnson melting furnace has never been used and has been stored for several years; it is in new condition with light surface rust on cast iron parts from storage. This one is set up for LP Gas with pipe gas connection of 1/4” diameter. The furnace is complete, never used, and still in shipping box.

(Sold) This controller from the furnace. Lennox/Johnson Controls 86H3001 Control Board G891TCA-8101(Sold) The furnace was replaced because the heat exchanger was leaking. The pictures are part from the furnace I saved.

This is a Johnson Gas Appliance furnace. this can be used to heat treat tooling or melt lower temperature alloys. The model is a 121 SD, Serial Number 648-T rated at 120000 BTU per hour.

Johnson Gas Appliance Co. Model 122-DW-ES natural gas furnace. Company still in business.

I have 2 gas fired bench furnace that was used primarily to heat large soldering irons to solder sheet-metal. One of the furnaces is a Johnson 101 and the other is a Reliable 2-S. I am asking $400.00 for both furnaces.

For Sale is a like new charcoal grey 2015 Central Boiler CL7260 Classic outdoor wood boiler/furnace. This is a commercial sized unit that can heat upwards of 18,000 sq. ft.

I am selling a used properly working board that was removed from a furnace that was getting replaced. The board has no issues and is in good working condition.

Natural Gas Heat Treat Furnace Draw Furnace Melting Furnace made by Johnson Furnace Company. This belonged to Cal State Los Angeles and was used very little. Perfect for smaller shop for heat treating die componets.

WATKINS-JOHNSON MODEL 8C-77(H)(S) 8" Wide BELT FURNACE MAX TEMP 1100C SN 3494 N2 H2 440V 33KVA 60HZ 3 Phase UNTESTED SOLD AS IS

This is a NEW Lennox Pulse Ignition wire set, No Lennox part #. Used on the pulse 21 furnace when switching to the johnson series of ignition controls. If you need this part you may need it fast, I will ship immediately after payment clears.

You are Looking at a new old stock Johnson controls penn surface mount temperature control A19 DAD-1 furnace parts . came from long time heating contractor retirement sale in original box instructions included LOOK AT PICTURES . Shipping from 44624 Shown on the E bay Shipping Calculator which should be close to actual .

Honeywell, Model S8610U Universal intermittent Pilot Ignition Control Module Honeywell Continuous re-try 100% shutoff IP 90 sec. trial for ignition. Removed from a working furnace.

New unboxed. Photo 7 shows unit's plug on bottom, furnace's required socket on top. (unit has PC board edge connector, cable has mating connector opposite the plug end) This is recent model with edge connector, but cable lets it interface with older models.

G776RGD-11 Intermittent Pilot Ignition Control (IPI) Used and in good working condition. Thanks

Control board was taken off of fully functioning furnace.

Rotom RFB547 Flue Exhaust, Draft Inducer Blower Kit. Use with Lennox, Armstrong Air-Ease Units. Models High Efficiency Air-Ease Ultra 90, 290 Lennox G26