mounted motor for sale, brand-new and used.

SPAN.skype_pnh_container SPAN.skype_pnh_mark { DISPLAY: none! important } @media Screen { SPAN.skype_pnh_print_container { DISPLAY: none! important } SPAN.skype_pnh_container { CLEAR: none!

Moeller motor disconnnect switch P1-25 Moeller P1-25 25 AMP surface mounted disconnect switch.Black padlockable handle (Emergency Stop) rated NEMA 3R, 12, IP 65.

Aximax 2 Vaneaxial Fan, 115 VAC, 0.33 A, 400 Hz, 20,000 RPM, 58 CFM, 0.5 uF CAP Series 368YS The Aximax 2 fan, like other vaneaxial fans, has both aerodynamic impeller blades and stationary guide vanes to enhance static pressure efficiency. These high speed fans achieve maximum performance

Introduction: This Arduino Compatible Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current. This shield can be directly mounted onto standard Arduino Duemilanove and Arduino Mega. Speed control is achieved through conventional PWM which can be obtained from Arduino’s PWM output Pin 5 and 6.

Each set INCLUDES 4 of these large, powerful MAGNETS NEW IDEA: More Stable, More Powerful Lab Stirrers ...Working in a lab with magnetic stirrers ??Want to increase capacity and stability of your s

RK27112MC usa shop E-Mail Contact Shipping cost Widerrufsbelehrung

DM-MOTIN

This listing is for 1 RoboClaw 2x15A Motor Controller The RoboClaw 2x15A motor controller by Ion Motion Control can supply two brushed DC motors with 60 Amps continuous and up to 120 Amps peak. With its multi mode interface it can be con

This listing is for 1 RoboClaw 2x5A Motor Controller The RoboClaw 2x5A motor controller can supply two brushed DC motors with 5 Amps continuous and up to 10 Amps peak. With its multi mode interface it can be controlled from standard RC radio, serial devices, analog and or microcontrollers such as an Arduino or Raspberry Pi. Dual quadrature encoders with up to 19.6 million pulses per second are supported.

Motor controller removed from a Sieg X1 mill and mounted in a metal enclosure. The controller is designed to change speed of a 90vdc 1/5HP motor. The volt meter in the pictures is not included.

This listing is for the most advanced motor connectors offered to date for the Gecko G540 stepper controller along with 3 10ft premade (ZERO ASSEMBLY REQUIRED) DB9 motor cables with gender changers. These connectors can be typically used on any controller that utilizes a DB9 female port or modified for other controllers. Please read this listing closely while reviewing the pictures, and you will realize the potential of this simple system.

Stepper Motor Screw with Mountable Slider. Small Stages 2-phase 4-wire Specification: Motor type: 2-phase 4-wire Driving voltage: DC4-5V Screw length: 73mm Effective stroke: 63mm Screw pitch: 3mm Step Angle: 18 ° Stages size: 90 * 30mm Description: Stepper Motor mounted on high quality aluminum frame with two rails to guarantee consistent, accurate movement

Induction motor with built-in reverse gear RD-09 use as a control motor in servo systems of automatic devices, slot machines, electrical, flow metering of liquids, granular materials.RD-09 Geared motor consists of a reversible AC motor and multistage cylindrical gear reducer.Motor and reducer are structurally located in one housing.Optionally, this motor is equipped with crossbar, mounted on the shaft.

Up for sale is one used Dunkermotoren PM DC Motor GR 42x40 88832-D2191 24V(refer to pictures); W/Toroid Transfomer S2585701 Prim 2X115 50/60 Hz bl-br/re-01 gn-gn SL 9338; W/Graf Gantner Electric switchable 110-220V SILA6/SUPPLY02 Power Supply HT2492; Three prong 110-220V switchable power switch. The motor is mounted on a vibration isolating mounting plate. The driven two finger prong device performs an eccentric left-right motion.

Adapter Plate For Mounting a NEMA23 motor to a Metric Linear Slide (Frame 60mm)