taper cutter for sale, brand-new and used.

1 7/32" SPOT FACER COUNTERSINK HIGH SPEED TAPER SHANK COUNTERBORE AND SPOT FACER FOR INTERCHANGABLE PILOTS 1 7/32" DIA WITH TAPER SHANK 5 FLUTE CUTTER 3/8 PILOT HOLE 5/32 WRENCH USED IN EXCELLENT CONDITION PLEASE SEE ALL PICTURES FOR DETAILS THANKS FOR LOOKING PLEASE SEE MY OTHER LISTING FOR MORE

CLEVELAND TWIST 20719 HIGH SPEED TAPER SHANK COUNTERBORE AND SPOT FACER FOR INTERCHANGABLE PILOTS 1 1/16" DIA WITH TAPER SHANK 3 FLUTE CUTTER USED IN EXCELLENT CONDITION PLEASE SEE ALL PICTURES FOR DETAILS THANKS FOR LOOKING PLEASE SEE MY OTHER LISTING FOR MORE GAGES AND MACHINIST TOOLING Check out my other

CLEVELAND TWIST W7189 HIGH SPEED TAPER SHANK COUNTERBORE AND SPOT FACER FOR INTERCHANGABLE PILOTS 1 3/4" TAPER SHANK 5 FLUTE CUTTER 7/16 PILOT HOLE USE 5/32 WRENCH USED IN EXCELLENT CONDITION I HAVE QUANTITIES IN CASE YOU WANT MORE THAN ONE PLEASE SEE ALL PICTURES FOR DETAILS THANKS FOR LOOKING

CLEVELAND TWIST S75 HIGH SPEED TAPER SHANK COUNTERBORE AND SPOT FACER FOR INTERCHANGABLE PILOTS 1 11/16" DIA WITH TAPER SHANK 5 FLUTE CUTTER 7/16 PILOT HOLE 5/32 WRENCH USED IN EXCELLENT CONDITION PLEASE SEE ALL PICTURES FOR DETAILS THANKS FOR LOOKING PLEASE SEE MY OTHER LISTING FOR MORE GAGES AN

Here we have a Nice used threaded Bolt end, looks like it would mount in the end of a horizontal mill cutter arbor or even in to the drawbar threads of most 50 taper tool holders. Overall length is 3-3/4" Shank size is 1-1/2" x 1-3/4" long then the 45 degree angle taper starts The threads are 1" - 8 TPI right hand

This is for One very nice used counter sink/counterbore tool holder without any cutters for it. 5mt shank This one does have the snap ring up inside it. I believe it helps to keep the cutter from falling out if your spindle stops too fast but it is not necessary for using it.

This is for One Good used counter sink/counterbore tool holder 1mt. This one does not have the snap ring up inside it. I believe it helps to keep the cutter from falling out if your spindle stops too fast but it is not necessary for using it.

On this tool the shank is morse taper but it does not cut a morse taper, details about the cut are below.

Description: New 1pcs HSS 6Flute Dia 16mm 60degree Morse Taper Shank Countersink Drill Cutter Specification: Cutter dia: 16mm Morse Taper Shank: MT1 (Morse #1)

This is a nice used master holder for holding cutters that have the Devlieg hex drive shank, Gairing also makes this same system but I am not sure if they are interchangeable. It is equipped with 3 cutters. The hex shank measures about .744" across the Flats.

We Have 1,000's of New And Used MetalWorking Machines And Tooling! If You Have Any Questions Or Are Looking For Something Particular Call Us @ 909.919.9600! NL Condition: Good Specifications: Bit Capacity: 1/2" Body Diameter: 3" Shank: 50 Taper Projection: 6" Overall Length: 11" Comes as shown in pictures

MORSE TAPER 3 COLLETS - IMPERIAL This Is A"Brand new" Set Of 11 Pcs. MT3 Collets used In Milling And Lathe Applications. With This Set You Can Hold The Most Common Cutter Sizes.

MORSE TAPER 2 COLLETS This Is A"Brand new" Set Of 7 Pcs. MT2 Collets used In Milling And Lathe Applications. With This Set You Can Hold The Most Common Cutter Sizes.

MORSE TAPER 3 COLLETS - METRIC This Is A"Brand new" Set Of 15 Pcs. MT3 Collets used In Milling And Lathe Applications. With This Set You Can Hold The Most Common Cutter Sizes.

This tool does not cut a morse taper, but the cutting edges are tapered, details about the cut are below Item ...................... Standard Straight Fluted Tapered pin Reamer

Ridgid 65790 00-R Pipe Threader Die Head, 1" BSPT, With High Speed RH Dies Features The 00-R style is available in 1/8”, ¼”, 3/8”, ½”, ¾”, and 1”. Current-catalog style. All parts are available and supported by Ridgid.