Trailer Lighting set fits Tamiya, Wedico, Bruder Truck Hauler, US $37.72 – Picture 0

Trailer Lighting set fits Tamiya, Wedico, Bruder Truck Hauler, US $37.72 – Picture 1

Trailer Lighting set fits Tamiya, Wedico, Bruder Truck Hauler, US $37.72 – Picture 2

Trailer Lighting Set Fits Tamiya, Wedico, Bruder Truck Hauler

US $37.72

Clevedon, United Kingdom
Jan 30th

Open on mobile:
QR code

This is a complete set for TRAILER lighting and will give rear/brakes, turn indicators and reversing lights. This will work with almost any radio set up as it requires only access to the steering and throttle channels via a built in Y lead arrangement. This can therefore be used with any existing truck set up from lighting sets up to and including Beier, Servonaut and Tamiya MFU systems. It provides a simple and cost effective way to provide lights for your trailer(s) without breaking the bank. We have a separate item fro the truck lighting. The set comprises of our truck lighting set and a specially manufactured extension cable. The extension cable provides combined "y" leads for radio, an interim 4 way latching connector that will easily unlatch and along tail to run into the trailer wher it attaches to the "second" lighting set. NB. This set works entirely separately to any other control. It will work with any standard ESC including MFU but operates entirely separately. This will NOT work correctly with cruise control ESC's. The lighting set comes with a controller, two "Y" leads (which are not required) and 6 sets of LED lights. The LED's consist of 2prs 5mm White, 1 pr 3mm white, 2 prs 3/5mm amber, (use the 5mm ones for the trailer light buckets, 3mm can be used as auxiliary indicators) 1 pr 5mm red. These are the long lead versions. The set has 8 outputs. The set has 3 plug selectable options to determine actions. Plug A reverse the throttle channel activity Plug B reverses the Steering Plug C selects the activity on Channel 8 In use the "Y" lead connect the unit to the Receiver and their associated outputs (throttle and steering). Output 1 is at half bright at all times except moving forwards when it is full brightness (can be used for e.g. marker lights) Output 2 is fully bright when going Forwards Outputs 3 and 4 flash in turns Output 5 mimics output 1 Output 6 is on when running in reverse Output 7 mimics a beacon two quick flashes with a short space and repeat. Output 8 with the link out is on when braking, with the link in it is on half bright except when going from fwd to reverse (braking). Extra lights are available please see our other listings. The kit comes with double sided tape to mount the unit, self adhesive cable clips, and tie wraps to keep it all tidy. Supplied in a presentation box so this would make an excellent present! For 5/6 volt use, takes its power direct from the Receiver. Installation is simple: 1. Confirm the size and installation position of LED lights, then marked. 2.Drill some LED holes on the car body. 3. Insert all the cables to the corresponding sockets of the LED System Control Board. 4. Connect the Y-cable (CH1) long end with the LED System Control Board (CH1), two short ends with the steering servo and receiver“channel 1”. 5. Connect the Y cable (CH2) long end to the LED System Control Board (CH2),two short ends to the throttle servo( or ESC)and received “channel 2”. 6. Stick the LED System Control Board on a suitable position of the car body. 7. Fix the LED lights into the holes and make sure it is installed firmly. 8. Fix all the over long cables with the accessories.

Condition:

New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...

Accessory Type

Lights