1 1 2 muffler for sale, brand-new and used.

This Is an Exact Replica Ball Muffler For the 1 1/2 1 3/4 & 2 Hp Hercules, Economy, & Jaeger Hit & Miss Or Throttle Governed Gas Engines Using A 1" Pipe Thread For the Exhaust. This is 7" In Dia ..... 5 1/2 " tall 1 " Pipe thread......

This Is an Exact Replica Ball Muffler For the 1 & 1 1/2 Hp Sparta Economy Hit & Miss Gas Engines Using A 1" Pipe Thread For the Exhaust. This is very similar to the Ball Mufflers that were used on the various Early Hit & Miss Gas Engines This is 7" In Dia ..... 4 1/4 " tall 1 " Pipe thread......

This is a Rusty Ball Muffler For the Later Waterloo & Waterloo Contract Hit & Miss Gas Engines, All The Small H & K Waterloo Boy 1 1/2 1 3/4 with the 3/4" exhaust Used these Mufflers, As it shows them in the Sales books..... Fits: 1 1/2 1 3/4 & 2 Hp Sizes.. With 3/4" Exhaust Pipe I would say that if you Have any Waterloo Or Waterloo Contract Engine, That Uses A 3/4 Pipe thread this would be the correct style muffler for your Engine This is 6 1/2" In Dia

This is a New Replacement Ball Muffler For the Later Waterloo & Waterloo Contract Hit & Miss Gas Engines, All The Small H & K Waterloo Boy 1 1/2 1 3/4 with the 3/4" exhaust Used these Mufflers, As it shows them in the Sales books.....

This is a New Replacement Ball Muffler For Any Engine That Uses A 1 1/4" Pipe thread For the exhaust, It is Like Many Of The Mufflers That Were Made back Then & was used On Many Brands & Models Of Hit & Miss Gas Engines. This Is Bolted Together Like the Originals Were With 5/16" Square Nuts & Bolts, They were used On The Galloway, Associated, United, Witte, Amanco, 6 Hp John Deere, & Many Others, Basically anything with 1 1/4" Pipe thread Or Whatever You Can Adapt it to !!!!

Here is a great muffler which fits many engines and looks great on any of them. This is a cast iron reproduction muffler. It is sand cast just as original and is fastened with un-plated square head 5/16" bolts.

This Is an Exact Replica Cone Style Muffler For the 1 1/2 1 3/4 & 2 Hp Economy, Jaeger, & Arco Hit & Miss Or Throttle Governed Gas Engines Using A 1" Pipe Thread For the Exhaust, I have seen this muffler Used on the later XI & XK, JI & JK Economy Engines. This is 6" In Dia ..... 3 " tall 1 " Pipe thread......

This is a nice reproduction ball muffler for a gas engine. It was cast aluminum and someone has smoothed and polished it. They did a really nice job and would look really nice on your restored engine.

Here is a muffler from a vintage gasoline engine. This collectible gas engine muffler measures about 4-1/2" around and 3" wide with a 1" male pipe thread nipple attached. Looks to be in good condition with only surface rust and some small dents though at some point there has been a 1" x 3/4" bell reducer added.

Here is a vintage muffler that may have been from a snowmobile, tractor, gas engine or antique vehicle. This 9" long x 5" round muffler body has a 1-1/2" inlet flange with two 3/8" bolt holes, one slotted, about 2-11/16" apart mounted at about a 30 degree angle to the main body and a curved 1-1/2" outlet that is about 5" long. There is a 1/4" mounting stud on one end and a hoop approximately half way on the opposite side.

Here is a muffler from a vintage gasoline engine. This collectible gas engine muffler measures about 4" around and is about 3" thick with a 1" male pipe thread nipple attached that is about 4-1/2" long. Looks to be in good solid condition with only surface rust and some pipe wrench marks.

This is an original cast iron ball type muffler for a hit and miss or throttle governed gas engine. These were commonly used on Economy engines and several others. They look and work good on any engine they fit on!