US $50.00
Condition | Used
:
An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
|
Seller Notes | “Name stamped in end of blocks” |
Directions
Similar products from Supporting Blocks & Sets
2 Parallels Machinist 9" & OTHER MACHINIST BLOCKS WHITNEY PRATT 18" H118L & F58L
LARGER 4 1/2 POUND MACHINIST V-BLOCK AND CLAMP
V-Block, 6" x 6" x 6", 1-1/4 to 4-3/8" V Capacity, 90° V Angle
L.S.STARRETT #278 V-BLOCK SET W/CLAMPS ***SUPERB***!
1-2-3 Setup Blocks, Matched Pair, 23 Holes (5 Tapped), .0001" Squareness (52C)
2 Tool Workholder Benchtop Vice Clips Vertical Hold Down Toggle Clamps DESTACO
STARRETT NO. 129 BENCH BLOCK WITH BOX
MACHINIST LATHE MILL Lot of Machinist Gages Parts Cutters Hold Downs Parts Etc
MACHINIST LATHE MILL Lot of Machinist Tap Wrench Scraper Collet Closer Parts Etc
small ~ Magnetic V-Block -- small ~ V-Block
MACHINIST LATHE MILL Lot Machinist Stainless Hardware Bushings Collets Parts Etc
BROWN AND SHARPE NO. 750A V BLOCKS WITH CLAMPS MACHINIST TOOLING
STARRETT NO.567 V BLOCK AND CLAMP WITH BOX
Bridgeport wise jaw for angle milling,lot of grained parallels
PAIR I BEAM MACHINIST TOOLROOM MOLD MAKER PARALLELS
PAIR I BEAM MACHINIST MOLD MAKER PARALLELS
Machinist V Blocks Clamp Set Of 3
MACHINIST JIG FIXTURE ?? 6"D TOOL MAKER MILLING LATHE
Machinist Right Angle Set Up Block TOOL MAKER MILLING LATHE
People who viewed this item also vieved
SET OF DOUBLE TAPER TREE MILL COLLETS 1/8 - 1"
Blind Hole Slide Hammer T-handle slide hammer 8 Collets Bearing Internal Remove
Techniks Close Tolerance CNC ER 25 5/16" Collet
Mitee-Bite 4" Long TalonGrip Steel Vise Jaw Set for 4.0" CNC Mill Vises
Machinist Made 4" Dia. x 1" Drawbar Face Plate 4 Clamps Tool Diemaker Grinder
Stub Milling Machine Arbor - Length of Shoulder To Nut: 3'
Abbott KTT12JN Jaw Nuts For 1.5mm x 60 Degrees Serrated Chucks - CHUCK SIZE: 12
Gator 1-201-0601 Self-Centering Scroll Chuck - CHUCK SIZE: 6'
TTC SF8100T1 1.5mm x 60 Degrees Serrated Jaws - Pack of 3
VRARE HUGE ARMSTRONG No.1408 HEAVY DUTY 8" C CLAMP MADE IN USA CHICAGO HEAVY
4 VINTAGE MACHINIST PARALLEL CLAMPS possibly brown and sharpe not marked
ARMSTRONG 6" C-CLAMP PART NUMBER 78-106
KURT VICE JAWS HARDENED + GROUND 6" WIDTH STEEL VICE JAWS
BRIDGEPORT VISE 6 INCH KEYED FOR A FADAL CNC LOCAL PICK UP ONLY
FACTORY KURT VICE JAWS HARDENED + GROUND 6" WIDTH Steel Vice Jaws
Greenfield 320-3210 (RC) Radial Drive Holder #2 Morse Taper Shank
Kennametal Metcut 300-2215 #2 Morse Taper Shank #2 Pin Drive Holder
47" x 47" TOSHIBA/SHIBAURA POWER ROTARY TABLE - #27038
CAMCO INDEX DRIVE ROTARY TABLE 1800RDM3H64-330 WITH 5HP MOTOR TESTED GOOD
HAAS 4th AXIS 5C14 PIN ROTARY INDEXER AND CONTROLLER WITH MANUAL CLOSER S5C HA5C
"Karbonz Single Pointed Needles 14""-Size 3/3.25mm"
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies