1 3 4 muffler for sale, brand-new and used.

Westward Muffler Splitter Chisel, 0.401 In., 7-1/2, New RETAIL PRICE IS $18.00 Rivet Hammer Chisels Durable, heat-treated alloy steel promotes long life. Shank Size: 0.401 Shank Shape: Round Collar Type: Round Overall Length: 7-1/2" For use with most brand name air hammers Payment Methods: You may pay instan

Bosch Pneumatic Reversible Tapper / Druckluft-Gewindeschneider Model 0 607 461 413 Made in Germany Brand new and unused. Please look at the photos closely. The tapper has been sitting in the original box and accumulated a very small bit of surface rust on the blued parts and a muffler is not included.

Product Description:Durable DuroMax 7.0 Hp, air cooled OHV engine with low oil shutoff . Heavy duty steel frame with four point fully isolated motor mounts for smooth and quiet operation. Full power panel with engine shutoff switch, volt meter, circuit breaker and power outlets.

I have a new old stock muffler for a 4.0 Onan Generator. Bought this from a old mechanic and it was stored in the attic of a old building. The body reads NELSON muffler embossed.

This Is an Exact Replica Ball Muffler For the 1 1/2 1 3/4 & 2 Hp Hercules, Economy, & Jaeger Hit & Miss Or Throttle Governed Gas Engines Using A 1" Pipe Thread For the Exhaust. This is 7" In Dia ..... 5 1/2 " tall 1 " Pipe thread......

This Is an Exact Replica Ball Muffler For the 1 & 1 1/2 Hp Sparta Economy Hit & Miss Gas Engines Using A 1" Pipe Thread For the Exhaust. This is very similar to the Ball Mufflers that were used on the various Early Hit & Miss Gas Engines This is 7" In Dia ..... 4 1/4 " tall 1 " Pipe thread......

This is a Rusty Ball Muffler For the Later Waterloo & Waterloo Contract Hit & Miss Gas Engines, All The Small H & K Waterloo Boy 1 1/2 1 3/4 with the 3/4" exhaust Used these Mufflers, As it shows them in the Sales books..... Fits: 1 1/2 1 3/4 & 2 Hp Sizes.. With 3/4" Exhaust Pipe I would say that if you Have any Waterloo Or Waterloo Contract Engine, That Uses A 3/4 Pipe thread this would be the correct style muffler for your Engine This is 6 1/2" In Dia

This is a New Replacement Ball Muffler For the Later Waterloo & Waterloo Contract Hit & Miss Gas Engines, All The Small H & K Waterloo Boy 1 1/2 1 3/4 with the 3/4" exhaust Used these Mufflers, As it shows them in the Sales books.....

This is a New Replacement Ball Muffler For Any Engine That Uses A 1 1/4" Pipe thread For the exhaust, It is Like Many Of The Mufflers That Were Made back Then & was used On Many Brands & Models Of Hit & Miss Gas Engines. This Is Bolted Together Like the Originals Were With 5/16" Square Nuts & Bolts, They were used On The Galloway, Associated, United, Witte, Amanco, 6 Hp John Deere, & Many Others, Basically anything with 1 1/4" Pipe thread Or Whatever You Can Adapt it to !!!!

This Is an Exact Replica Cone Style Muffler For the 1 1/2 1 3/4 & 2 Hp Economy, Jaeger, & Arco Hit & Miss Or Throttle Governed Gas Engines Using A 1" Pipe Thread For the Exhaust, I have seen this muffler Used on the later XI & XK, JI & JK Economy Engines. This is 6" In Dia ..... 3 " tall 1 " Pipe thread......

Here is a muffler from a vintage gasoline engine. This collectible gas engine muffler measures about 4-1/2" around and 3" wide with a 1" male pipe thread nipple attached. Looks to be in good condition with only surface rust and some small dents though at some point there has been a 1" x 3/4" bell reducer added.

Here is a vintage muffler that may have been from a snowmobile, tractor, gas engine or antique vehicle. This 9" long x 5" round muffler body has a 1-1/2" inlet flange with two 3/8" bolt holes, one slotted, about 2-11/16" apart mounted at about a 30 degree angle to the main body and a curved 1-1/2" outlet that is about 5" long. There is a 1/4" mounting stud on one end and a hoop approximately half way on the opposite side.