1 inch pulley for sale, brand-new and used.

You are viewing a 2.5 inch pulley with a 5/8 bore Good Condition Because many of the items have been gently used, please expect some gentle wear. Payment Option: I accept Pay Pal. Your prompt payment is great

I have for your buying pleasure one pulley 5 inch in diameter with a 1/4 inch wide grove. There is a sealed bearing in the center of this pulley that turns smooth and free, with a bolt hole of about 1/4 of an inch in diameter. On the pulley is (AN-210-5A) (similar pulleys I recently sold also had 4-3/8 and FORMICA on them).

Old and well-built 1/3 hp Westinghouse motor that was used with a small air compressor. It is mounted on a metal plate that can remain or be removed with your preference.

var itemNumber = window.ebayItemID ?

Nice pulley old good repair on an edge chip 5 inch diameter 4 inches wide 1-1/4 shaft with set screw hole

NEW or like new 14.5 inch cast iron dual belt pulley / sheave / flywheel designed for an air compressor pump. Looks unused with no wear and 99% of OEM black paint. Center bore is for a tapered crankshaft.

This auction consists of an antique flat pulley or flywheel for a small stationary engine. It measures approximately 7-inches in diameter. The center hole is approximately 1-1/4 inch and it's 3-1/8 inch wide.

This is an extremely hard to find original cast iron flat belt pulley and mounting stub shaft for a 6hp John Deere E hit and miss gas engine. It is in excellent condition with no cracks, breaks, or repairs of any kind. The stub shaft is part number E2014R and the pulley has a 6 1/2 inch face and is 12 inches in diameter.

This is a real nice original cast iron pulley for an International Harvester Tom Thumb or 1hp Famous or Titan gas engine. It may also be correct for the 1hp Titan engines. It is part number G-6618 and is in excellent condition with no cracks, breaks, or repairs of any kind except for a small chip on one edge.

This is a real nice original cast iron pulley for an International Harvester 1 1/2-2 1/2 or 3-5hp LA or LB gas engine. It is part number 3591-D and is in excellent condition with no cracks, breaks, or repairs of any kind. It has a 5 inch face and is 4 3/4 inches in diameter.

This is a real nice original cast iron clutch pulley for a 2 1/2hp Mogul or 3hp Type M gas engine made by the International Harvester Company. It is in excellent condition with no cracks, breaks, or repairs of any kind except one repaired spoke on the carrier. A very nice job was done and it's very tough to notice especially when it's on an engine.

Here is a vintage Westinghouse Electric motor 1/3 HP, 1725 Rpm, 115 volt, 5.7 amps, 1 phase, Continuous hours, with a 6 inch pulley. tested and works great and quiet. missing electrical cover.

For sale is a CMC Rescue Pulley. Used for a 2 days of low to medium angle rope rescue training. Kept clean.

BELT DRIVE ALIGNMENT Fixturlaser PAT - the final solution to all your belt alignment needs! With the Fixturlaser PAT, you are never in doubt on whether your belt transmissions are aligned or not. By using the groove as reference, you will achieve a precise alignment which reduces belt wear, bearing failures and vibrations.

This is a real nice original cast iron pulley for an International Harvester 1 1/2hp Type M engine or a 1 3/4hp International Harvester Mogul engine. It is part number 969T and is in excellent condition with no cracks, breaks, or repairs of any kind. It has a 5 inch face and is 6 inches in diameter.

This is a real nice original cast iron pulley for an Ottawa hit and miss or throttle governed gas engine. At least I'm pretty sure it is for an Ottawa...if it isn't please educate me. It is in excellent condition with no cracks, breaks, or repairs of any kind.

Mechanical advantage of Block and tackle system is about saving labor when dragging or hauling.