1 pulley for sale, brand-new and used.

Powerful little 12v motor for many hobby applications. Motor comes with a V-Groove pulley for use with O-Ring belt or can be removed for straight shaft connection. Rubber grommet on output end was apparently a motor mount and can also be removed.

Emerson catalog # U25E2DC Motor Emerson Motors FEATURES

Baldor Motor, 15HP,1200RPM,3PH,60HZ,284T,TEFC, Features: 1.15 Service Factor Corrosion resistant epoxy finish Regreasable ball bearings Oversized rotatable cast iron conduit box Forsheda® shaft seal Moisture resistant copper windings Class F insulation Stainless steel nameplate and corrosion resistant harware Tropicalized Typical Applications: Typical applications include petro-chemical plants, mines, foundries, pulp and pape

90579 Used, Baldor FDL3504M Motor, 1/2 HP, Single Phase, 115/208-230V, 60 Hz, 7.4/3.9-3.7 Amps, 1725 RPM, 2-1/2" Shaft L, 5/8" OD, 3" OD of wheel, 15/16" Shaft length outside pulley. Electrical cable attached. Item shows signs of having been used - actual working function unknown.

SAVE $$$$ & TIME USE "BUY IT NOW" This Auction is for: Vintage MARATHON 1/6 HP ELECTRIC MFG CO. WASAU WIS. U.S.A.

This auction is for a brand new Dayton 5K117BD motor. It includes the motor, pulley, circuit breaker, belt and grease fittings. HP 3/4 HZ 60 V 115/208-230 Phase 1 RPM 1725

Here is a nice Westinghouse 1/2 HP motor Type A. 1725 RPM, 115 volt, 7.2 amps, single phase, continuous rating, thermal protection,and ball bearings. Shaft size is 1/2" dia.

YOU ARE BIDDING ON A NEW IN BOX EMERSON 1/2 HP ELECTRIC 1 SPEED MOTOR, EVAPORATIVE COOLER MOTOR KIT,MADE BY MASTERCOOL CLOCKWISE ROTATION-SHAFT END NON REVERSIBLE 230VOLTS AC 60HZ, 1725 RPM OPEN CONSTRUCTION, 56Z FRAME, SHAFT SIZE IS 1/2" INCH.

YOU ARE BIDDING ON A NEW IN BOX EMERSON 1/2 HP ELECTRIC 2 SPEED MOTOR, EVAPORATIVE COOLER MOTOR KIT,MADE BY MASTERCOOL CLOCKWISE ROTATION-SHAFT END NON REVERSIBLE 230VOLTS AC 60HZ, 1725/1140 RPM OPEN CONSTRUCTION, 56Z FRAME, SHAFT SIZE IS 1/2" INCH.

This is a Walker-Turner (WT) Driver Line "Custom Built Ball Bearing" Motor from the late 1940's, Catalog No. 9331, manufactured by the Walker-Turner Division, Kearney & Trecker Corp, Plainfield NJ. It's in super-nice condition.

Up for sale is a Dayton 1/2 hp single phase motor. Item is in good usable condition. 1/2 hp, 115 volt, 208/230 volt 8, 3.0/4 amps.

MARATHON 1/4 HORSE ELECTRIC MOTOR WITH PULLEY AND MOUNTING BASE. 1725 RPM. MODEL# FQA48S17D595H THESE ARE NICE IN THAT THEY HAVE INTERNAL LUGS SO THAT ROTATION CAN BE EITHER CW OR CCW.

ebay 8 ebay2 ebay Click pictures to vi

ebay 8 ebay2 ebay Click pictures to vi

EMERSON 1/4 HORSE ELECTRIC MOTOR WITH PULLEY AND MOUNTING BASE. 1725 RPM. THESE ARE NICE IN THAT THEY HAVE INTERNAL LUGS SO THAT ROTATION CAN BE EITHER CW OR CCW.

up for bid is a older working motor 3/4 Hp,, rpm 3450,,4.6 amps ,,60 cycle 110/230 volts it is CC rotation looking at pulley 2 1/2 stone is 5 1/2 " motor run in both dirictions depending on how you jump start some surface rust run fine once started,, 5/8 shaft shipping based on 50lbs packed Thanks Good Luck

Large older Century 1/2 HP Motor 1750 RPM with 3/4" shaft and the 3 1/4" OD pulley will come with it. 110-230 volt CHS-81-BH4-3FA code L 7 amp /3.5 at 230V currently on saw and runs very quietly upon request I can get shaft size etc.

Welcome to my site! Up for sale is a General Electric 1/2HP Motor Tag information is as follows: Model: 5KCP19SG356X V 208-230/220 HP 1/2 RPM 3450/2850 Code C A 2.30/2.40 Hz 60/50 PH 1 SAU Time Rating Cont Class B ROT CCW CAP 12.5-10/10 MFD