1/8 bit for sale, brand-new and used.

This is a brand new, never used 3/8" cutting diameter flush trim straight router bit with a 3/8 inch bearing and two carbide flutes. Flush cut bits are used primarily for flush cutting edges to a template, guide or jig. The bearing at the end is of the same diameter as that of the cutting depth so that the cutters will clear all material outside any template the bearing rolls along.

This is a brand new, never used 3/8" cutting diameter flush trim straight router bit with a 3/8 inch bearing and three carbide flutes or blades for superior smoothness, speed, and consistency of cut. Flush cut bits are used primarily for flush cutting edges to a template, guide or jig. The bearing at the end is of the same diameter as that of the cutting depth so that the cutters will clear all material outside any template the bearing rolls along.

This is a brand new, never used 1/2" cutting diameter straight router bit with two carbide flutes (blades) and a special gullet between cutting edges that allows for material clearing in mortising applications. The geometry of the blades and the open space between them is designed to allow for clean edge and clear bottom mortising up to about 3/8" depth for shallow hinges.

This is a brand new, never used 3/8" cutting diameter straight router bit with two carbide flutes or blades. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or an added shank bearing, for flush cutting edges to a template. This bit fits all 1/2" shank portable and table routers.

This is a brand new, never used 5/8" cutting diameter straight router bit with three carbide flutes or blades for superior smoothness, speed, and consistency of cut. Straight bits are used primarily for clearing dado channels for woodworking joinery, or, in conjunction with a router plate guide bushing or an added shank bearing, for flush cutting slab edges to a template. This bit fits all 1/2" shank portable and table routers.

Brand new, never used 10 degree dovetail router bit with 3/8" cutting diameter at the widest point, carbide edges and 1/2" shank. These bits are used for woodworking joinery along with a jig, or guide. The tapered dovetail shape makes alternating passes through one panel and opposite passes through another allowing for both straight end to end joining as well as right angle joints.

Hello and thank you for looking at my item(s)... For sale is a 3/8 in. Rabbit cut router bit.

CLE FORGE, 1/2" Morse Taper #2 Drill Bit - MT#2 - HSS, 8-1/4" Overall Length, Used - Has Surface Rust - May Need Sharpening Ask questions and check out the photos carefully as I don't offer refunds except when I make a huge error in the listing. Shipping is $6. You will need to specify if you wish insurance.

Fun Filled Auctions! Up for auction is a drill bit that is 2.6 mm in diameter which is very close to 7/64 inches in diameter. (Actually 7/64 inches equals 2.7781 mm).

All items are sold as is without warranty unless specifically stated in the posting. This does not mean that the unit doesn’t work, only that we have not tested or checked it out. This may also mean that we are not knowledgeable in this specific item.

Roper Scientific MASD Kodak Megaplus 4.2i 10 bit Digital Camera Free pick up or you can send your own label Here is the information from internet: The MegaPlus 4.2i is a high-performance digital camera that combines a spatial resolution of 4.2 million pixels, with up to 1024 gray levels for each pixel to deliver superior quality digital images. The CCD sensor provides a 2029 x 2044-pixel array with 9 µm square pixels for unsurpassed sensitivity and accurate dimensional measurements.

Specification Image CMOS Sensor Controller High Speed DSP (Driver Free available) Snap Shot Software and Hardware Still Image Capture Frame Rate 30 f/s under 600 LUX Brightness Digital Zoom 5X Sequence Mode Brightness Control Manual adjustment Power Supply USB 2.0 Port ( 5V DC ) USB 2.0 &USB 1.1 Compatible OPERATION SYSTEM: WINDOWS XP, VISTA, WIN 7 32 BIT ONLY!!!!!!

var itemNumber = window.ebayItemID ?

.shippingcalculator a { display:block; width: 208px; padding:177px 0px 10px 0p