US $1900
| Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
MILLING MACHINE TOOLS | TABLE CLAMP T BOLTS |
Directions
Similar products from Fittings & Plates
USED Precision Steel Angle Plate 1-5/8"x6"x6"x8" (JT)
AR- 223 GUNSMITH ARMORERS LOWER RECEIVER NON- MARR VICE BLOCK & W-W SPRING KIT
VINTAGE 5" FACE PLATE 1-1/2" x 8 TPI ATLAS CRAFTSMAN SOUTH BEND LOGAN LATHE
VINTAGE 6-1/2" FACE PLATE 1-1/2" x 8 TPI ATLAS CRAFTSMAN SOUTH BEND LOGAN LATHE
ADJUSTABLE, ROTATING,TILTING,MILLING DRILLING HOLDING ATTACHMENT NICE OLD STRONG
Parallels, General No. S-112-6 Adjustable Parallel Set, 3/8" to 2-1/4", USA
H/V 5C Horizontal & Vertical Collet Fixture Drill Milling Lathe Grinding
Rayco fixturing 1/4-20 adjustable Angle Plate R20-AAP
SUBURBAN Sine Plates Precision 4" x 4" x 2" S0 Steel 3/8-16" Hole SP44S0 |LU1|
lot of 2 Surface Grinder Grinding Cube Block Jig Fixture 7x4x1 1/2''
DPMS .223/5.56 Panther Claw Vice Block
MACHINIST LATHE MILL NICE Ground & Hardened Set Up Block Fixture Hold Down
3 1/2"x 2 3/4" x 2 1/2' RIGHT ANGLE PLATE FIXTURE No.4 machinist tools 3 pounds
MACHINIST LATHE TOOL TAFT PIERCE 4x4x6 Machinist Hollow Riser Block Cast Iron
HARDINGE FACE PLATE C-27 9 INCH FACE PLATE T-SLOTS TAPPED HOLES
Hardinge 7 In Face Plate, With Harding Taper Lock, Tool No. C-26
Machinist ANGLE PLATE with Vee Block Built In, Tapped All Over, 3.75" H WL
5 1/8" DIAMETER DRIVER DRIVE DOG FACE PLATE MACHINIST LATHE TOOL 1 1/2" x 8 TPI
Southbend lathe milling attachment for 9 or 10 in lathe
PAIR OF 10” INCH HOLD DOWNS MACHINIST TOOLS (LUFKIN 902)
People who viewed this item also vieved
ER20 5.5MM Komet Collet A33530000550
VCFC1678 5/16" Valenite Coolit Collet 93-371-1380
VCFC1656 Valenite CoolitbCollet 93-371-1379
DESTACO 607 CLAMP Detroit Stamping De Sta Co
DESTACO 235-U HORIZONTAL TOGGLE CLAMP 235U Detroit Stamping De Sta Co
One Starrett No.161-D Tool Makers, Machinists, Parallel Clamp
Very Nice Low Profile Milling Machine etc Vise 3 1/2" wide
9 CUTTERS FOR UNIMAT SL1000/DB200 LATHE NEW!
VINTAGE 6'' COLUMBIAN BENCH VISE - #506 LOCAL PICK UP ONLY!
Enco # 751 Live Center w/ # 1MT / FB 9
MT6 CARBIDE TIPPED CENTER MILLING GRINDING WORKHOLDING
Heavy 8 3/4" Long Large Live Center From Vintage Metal Lathe 1.25"-1.05" Taper
Set of 3 daco Soft Chuck Jaws square key type summit Gisholt Warner Swasey
NOS Cushman 4 Inch Lathe Chuck
6 jaw chuck for lathe for watch repair watchmaker lathe
8x LOT NEW ALSTOM POWER NUT GP-2375-B 1-5/8" HEX HEAVY JAM 1-5
Used Edward Andrews Steel Boring Bar Sleeve, 4" L, 1.5" OD, 1/2" Bore, EA48-1
Used Edward Andrews Steel Boring Bar Sleeve, 1.50" O.D., 4" Length, EA48-2
ISTEMA EDM 3R 20mm SHANK MOUNTING BLOCK FIXTURE PLATE * Machinist Toolmaker
machinist degree blocks milling set up 1 2 3 angle parallel Patrick standards
![TWO SETS OF TWO HARDENED PRECISION STEEL 1-2-3 BLOCKS [4 blocks total]](/_content/items/images/51/4175651/001.jpg)
TWO SETS OF TWO HARDENED PRECISION STEEL 1-2-3 BLOCKS [4 blocks total]
HRT210 HAAS Rotary Table 4th Axis
Troyke 15" rotary table model U15
PALMGREN Rotary Slide Tilting Table, 8 In, X-Y 4 jaw chuck
ROYAL TOOL HOLDER. ER 32 CAT 40 PN 54126
Collet Chuck for Brown & Sharpe #11 1-1/2" Straight Shank +3/8" Serrated Collet
DA-400 Double Angle Collet Chuck NMTB-50 Taper Shank
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies