US $470
| Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
Manufacturer | DPMS |
| Brand | DPMS | ||
| Country/Region of Manufacture | United States | ||
| Model | Panther Claw |
Directions
Similar products from Fittings & Plates
AR- 223 GUNSMITH ARMORERS LOWER RECEIVER NON- MARR VICE BLOCK & W-W SPRING KIT
VINTAGE 5" FACE PLATE 1-1/2" x 8 TPI ATLAS CRAFTSMAN SOUTH BEND LOGAN LATHE
VINTAGE 6-1/2" FACE PLATE 1-1/2" x 8 TPI ATLAS CRAFTSMAN SOUTH BEND LOGAN LATHE
ADJUSTABLE, ROTATING,TILTING,MILLING DRILLING HOLDING ATTACHMENT NICE OLD STRONG
Parallels, General No. S-112-6 Adjustable Parallel Set, 3/8" to 2-1/4", USA
H/V 5C Horizontal & Vertical Collet Fixture Drill Milling Lathe Grinding
Rayco fixturing 1/4-20 adjustable Angle Plate R20-AAP
SUBURBAN Sine Plates Precision 4" x 4" x 2" S0 Steel 3/8-16" Hole SP44S0 |LU1|
lot of 2 Surface Grinder Grinding Cube Block Jig Fixture 7x4x1 1/2''
12 - 3/4 MILLING MACHINE TABLE CLAMP T BOLTS & NUTS boring mill work holder tool
MACHINIST LATHE MILL NICE Ground & Hardened Set Up Block Fixture Hold Down
3 1/2"x 2 3/4" x 2 1/2' RIGHT ANGLE PLATE FIXTURE No.4 machinist tools 3 pounds
MACHINIST LATHE TOOL TAFT PIERCE 4x4x6 Machinist Hollow Riser Block Cast Iron
HARDINGE FACE PLATE C-27 9 INCH FACE PLATE T-SLOTS TAPPED HOLES
Hardinge 7 In Face Plate, With Harding Taper Lock, Tool No. C-26
Machinist ANGLE PLATE with Vee Block Built In, Tapped All Over, 3.75" H WL
5 1/8" DIAMETER DRIVER DRIVE DOG FACE PLATE MACHINIST LATHE TOOL 1 1/2" x 8 TPI
Southbend lathe milling attachment for 9 or 10 in lathe
PAIR OF 10” INCH HOLD DOWNS MACHINIST TOOLS (LUFKIN 902)
Lot - 8 PCS Lathe Drive Plate Machinist and Tool Holder Fixer Lathe South Bend
People who viewed this item also vieved
VCFC1678 5/16" Valenite Coolit Collet 93-371-1380
VCFC1656 Valenite CoolitbCollet 93-371-1379
12 Pcs. Phase II Hex & Square 5 C Collets With Inside & Outside Thread
DESTACO 235-U HORIZONTAL TOGGLE CLAMP 235U Detroit Stamping De Sta Co
One Starrett No.161-D Tool Makers, Machinists, Parallel Clamp
LOT OF MACHINIST PARALLEL CLAMPS work holding tool 1 ARMSTRONG No 12 & Others
9 CUTTERS FOR UNIMAT SL1000/DB200 LATHE NEW!
VINTAGE 6'' COLUMBIAN BENCH VISE - #506 LOCAL PICK UP ONLY!
Old 3" Machinist Drill Vise Model 108
MT6 CARBIDE TIPPED CENTER MILLING GRINDING WORKHOLDING
Heavy 8 3/4" Long Large Live Center From Vintage Metal Lathe 1.25"-1.05" Taper
NEW UNUSED MT1 60 DEGREE DEAD CENTER TOOL 4 ATLAS CRAFTSMAN 6" 618 LATHE
NOS Cushman 4 Inch Lathe Chuck
6 jaw chuck for lathe for watch repair watchmaker lathe
BUCK 4" 6-JAW LATHE CHUCK , 5 C MOUNT HARDINGE LATHE
8x LOT NEW ALSTOM POWER NUT GP-2375-B 1-5/8" HEX HEAVY JAM 1-5
Used Edward Andrews Steel Boring Bar Sleeve, 4" L, 1.5" OD, 1/2" Bore, EA48-1
Used Edward Andrews Steel Boring Bar Sleeve, 1.50" O.D., 4" Length, EA48-2
machinist degree blocks milling set up 1 2 3 angle parallel Patrick standards
![TWO SETS OF TWO HARDENED PRECISION STEEL 1-2-3 BLOCKS [4 blocks total]](/_content/items/images/51/4175651/001.jpg)
TWO SETS OF TWO HARDENED PRECISION STEEL 1-2-3 BLOCKS [4 blocks total]
STARRETT No.278 V-BLOCK SET OLD VINTAGE MATCHED TOOLMAKER INSPECT GRINDER MILL
Troyke 15" rotary table model U15
PALMGREN Rotary Slide Tilting Table, 8 In, X-Y 4 jaw chuck
Collet Chuck for Brown & Sharpe #11 1-1/2" Straight Shank +3/8" Serrated Collet
DA-400 Double Angle Collet Chuck NMTB-50 Taper Shank
15 Pcs Grand No21 Collet Set 1/8" to 1" + Chuck # 521 W/Wrench Made in Germany.
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies