US $7.50
Condition: |
New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is
applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details.
...
|
Brand | Specialized Tool Solutions |
Country of Manufacture | Canada |
Directions
Similar products from End Mills Router & Drill Bits
Weldon End Mill Bit B68-HS 1" Shank 4 Flute Flutes A 32-7 Length 3 11/16"
Hanita High Speed Steel HSS 1" x 1" x 4" x 6-1/2" 2 Flute Square Single End Mill
COUNTERSINK SET MACHINIST SEVERANCE NO 27-41 4 PIECE STEEL CASE FRESHLY SHARP
1/4" Carbide Endmill 3 Flute 5 degree taper per side Ballnose 1/2" shank TiAlN
5pc 1/4" Carbide Endmill 2 Flute Flat Bottom Reg TiAlN
1/4" Carbide Endmill 4 Flute .015" Corner Radius Regular TiAlN
3/16" Carbide Endmill 4 Flute .030" Corner Radius Regular TiAlN
7mm Carbide Endmill 2 Flute Flat Bottom Regular TiAlN
3/8" Carbide Endmill 8 Flute Flat Bottom Regular TiAlN
DOALL CORNER ROUNDING END MILL SET D-638 1/16" TO 3/8" HOLDER
5pcs 3mm Carbide Endmill 4 Flute Flat Bottom Regular TiAlN
OSG - 5485100 - Square End Mills 1" Dia 4 Fl Spiral Cobalt 5 1/2" OAL ***NEW***
25 Pcs. Used Endmills 3/4" Dia. cobalt Excellent Condition All USA MADE
Lot Y5 Over 60 Pcs. Used Endmills 1/2" and Under Excellent Condition
Lot G4 8 Pcs. Used Endmills 1" Rex 20 4 Flute Excellent Condition
Lot G3 Over 40 Pcs. Used Endmills 3/8" - 5/8" 2 and 4 Flute Excellent Condition
Lot G2 Over 20 Pcs. Used Endmills 1/2" 2 and 4 Flute Excellent Condition
Lot G1 Over 105 Pcs. Used Endmills 1/8" - 3/4" 2 and 4 Flute Excellent Condition
People who viewed this item also vieved
Mixed Lot Machine Tooling Lathes Mill
Assortment of Carbide Burrs 1/4" Shaft "New"
10 NEW KENNAMETAL DCMT 432LF CARBIDE INSERTS. GRADE: KC910. USA MADE {F439}
10 NEW SUMITOMO SEKN 53M CARBIDE INSERTS. GRADE: ACZ310 (F514)
2 REAMERS 13/16" #3 TAPER & 9/16" #2 TAPER
Greenlee RS232 25 Pin Connector D-Subminature Panel Punch
5 SETS OF HSS DIES 1/2" -13 NC TO 7/8" -9 WITH 5 DIE HOLDERS & 2-3/4" WRENCH
30 "NEW "HACK SAW BLADES BY "NICHOLSON" AND "MORSE" 12"LONG AND 24 TEETH USA,!
Milford 1/2" Profile Saw Blade S1204
Ceramic Turning Inserts TNGA 432 CC514 Qty 3 <2105>
SUMITOMO Ceramic Turning Inserts CNG433 WX2000 Qty 10 [2106]
25 Spline Gear Pull Broach 1.650" x 35" long
26 Spline Gear Pull Broach 2.3645" x 28" long by Ohio Broach
American Carbide Tool Carbide-Tipped Tool Bit for Threading Neutral C5 Grade ...
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies