US $89.97
Condition: |
Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully
operational and functions as intended. This item may be a floor model or store return that has been used. See the seller’s listing for full details and description of any imperfections.
...
|
Brand | DoALL |
Flutes | 4-Flute | ||
Model | D-638 | ||
Material | HSS |
Directions
Similar products from End Mills Router & Drill Bits
3/16" Carbide Router Bit 2 Flute Spiral Upcut with 1/4" shank
Weldon End Mill Bit B68-HS 1" Shank 4 Flute Flutes A 32-7 Length 3 11/16"
Hanita High Speed Steel HSS 1" x 1" x 4" x 6-1/2" 2 Flute Square Single End Mill
COUNTERSINK SET MACHINIST SEVERANCE NO 27-41 4 PIECE STEEL CASE FRESHLY SHARP
1/4" Carbide Endmill 3 Flute 5 degree taper per side Ballnose 1/2" shank TiAlN
5pc 1/4" Carbide Endmill 2 Flute Flat Bottom Reg TiAlN
1/4" Carbide Endmill 4 Flute .015" Corner Radius Regular TiAlN
3/16" Carbide Endmill 4 Flute .030" Corner Radius Regular TiAlN
7mm Carbide Endmill 2 Flute Flat Bottom Regular TiAlN
3/8" Carbide Endmill 8 Flute Flat Bottom Regular TiAlN
3/16" Carbide Endmill 4 Flute Flat Bottom Long 3/4" length of cut TiAlN
5pcs 3mm Carbide Endmill 4 Flute Flat Bottom Regular TiAlN
OSG - 5485100 - Square End Mills 1" Dia 4 Fl Spiral Cobalt 5 1/2" OAL ***NEW***
25 Pcs. Used Endmills 3/4" Dia. cobalt Excellent Condition All USA MADE
Lot Y5 Over 60 Pcs. Used Endmills 1/2" and Under Excellent Condition
Lot G4 8 Pcs. Used Endmills 1" Rex 20 4 Flute Excellent Condition
Lot G3 Over 40 Pcs. Used Endmills 3/8" - 5/8" 2 and 4 Flute Excellent Condition
Lot G2 Over 20 Pcs. Used Endmills 1/2" 2 and 4 Flute Excellent Condition
Lot G1 Over 105 Pcs. Used Endmills 1/8" - 3/4" 2 and 4 Flute Excellent Condition
People who viewed this item also vieved
Mixed Lot Machine Tooling Lathes Mill
Assortment of Carbide Burrs 1/4" Shaft "New"
10 NEW KENNAMETAL DCMT 432LF CARBIDE INSERTS. GRADE: KC910. USA MADE {F439}
10 NEW SUMITOMO SEKN 53M CARBIDE INSERTS. GRADE: ACZ310 (F514)
2 REAMERS 13/16" #3 TAPER & 9/16" #2 TAPER
LOT OF 5 HSS ROUND ADJUSTABLE DIES 20MMX2.5 TO 1" -14 UNF WITH 2" WRENCH HANSON
Greenlee RS232 25 Pin Connector D-Subminature Panel Punch
30 "NEW "HACK SAW BLADES BY "NICHOLSON" AND "MORSE" 12"LONG AND 24 TEETH USA,!
Milford 1/2" Profile Saw Blade S1204
Ceramic Turning Inserts TNGA 432 CC514 Qty 3 <2105>
SUMITOMO Ceramic Turning Inserts CNG433 WX2000 Qty 10 [2106]
25 Spline Gear Pull Broach 1.650" x 35" long
26 Spline Gear Pull Broach 2.3645" x 28" long by Ohio Broach
Hougen 12222 Rotabroach 1-11/16" x 2"
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
Accept All Cookies