3 phase table saw for sale, brand-new and used.

NOTE:

harrison 3 phase saw .good working order ,heavey duty hight 760mm length 1000 width 590mm been a good saw for me. thanks bill 07980025688

Powermatic Table Saw, Model 66. Serial #466546, 208/440v 3 Phase.....Biesemeyer T-Square w Stand includes two six foot edge pieces, a seven foot rail with measurements and two legs for extension stand & Brett-Guard - Table Saw Safety Guard and Guide - Model 10A NOTE: SHIPPING is NOT AVAILABLE for this item - LOCAL PICKUP ONLY. Due to the location of this item, this item can not be shipped.

1997 model, Baldor motor, Accufence (similar to Biesemeyer) with outfeed table. Includes motor cover, splitter (blade guard), arbor wrench, Uncut zero clearance insert, 4 each - 10" blades, dado set (not pictured), fence, bevel insert, PM66 user manual, PM66 owner's manual, Accufence Owner's manual, PM66 assembly instructions. Cash on pickup ONLY.

Powermatic model 68 table saw, 12" blade, cutting depth is 4-1/8". Rips through 4" of elm like most saws go through 3/4" pine. 3hp, 3 phase.

table size : 129" X 69"Max. cutting size: 149" X 84" Hydraulic tilting and rotating cutting table which needs work direct drive 2-speed 30 HP motor; holds up to 30" cutting blade Gear driven variable speed gantry and cross-travel;Gear motor driven rise and fall travel of 5.9" Solenoid water valve 220 3-Phase Overall dimensions are 21' X 16' X 11' ; total weight 11,000 lbs. Machine is currently operating and is available for inspection.

General Info: Stock #: JG-151006 Location: Stone Mountain, GA Brand: Delta Model: 34-802 SN: 92I96649 Year: N/A Weight: 450 LBS. Floor Dimensions: 63" x 42" x 32" Specifications: Blade Capacity: 10" Blade Tilt: 45° Right Table Top: 28" x 27" Cast Iron Arbor Size: 5/8" Max Rip Right of Blade: 32" Dust Port: 5" Motor HP: 3 Electrical: 115/230V(Wired 230), 1-Phase Equipped With: 32" Delta Fence Rails, Delta Unifence, 10" Blade, On/Off Switch, Cord & Plug. Additional Info: Unit has been

General Info: Stock #: JG-151008 Location: Stone Mountain, GA Brand: Delta Model: 438-02-314-0911 SN: N/A Year: N/A Weight: 300 LBS. Floor Dimensions: 40" x 31" x 60" Specifications: Blade Size: 12" Arbor Diameter: 5/8" Maximum Rip Capacity: 24" Maximum Crosscut: 13" Table Size: 30" x 26" Motor RPM: 3450 Motor HP: 1.5 Electrical: 115/230V(Wired 230), 3-Phase Equipped With: 12" Blade, Safety Guard, Key set to lock on/off switch, Cord & Plug Additional Info: Unit has been tested an

Baldor 3 hp TEFC Motor in excellent condition, bearing have no noise removed from a Powermatic 66 table saw shaft sises is 7/8 frame is 145tc runs on 208- 230-460 volt 3 phase

OLIVER 270D TABLE SAW 14 inch GREAT CONDITION with original manual  5 HP 3 PHASE DIRECT DRIVE MOTOR 3480 RPM 230/460 VOLT CURRENTLY WIRED FO

20” Powermatic Variable Speed Vertical Band Saw, Model 87 S/N 67-8235 Machine Specs: Throat 20” Max Height 12” Table Size 24” x 24” Table Tilts 5 & 45 Degrees Blade Speeds 40 - 4500 RPM Blade Size 1/8 to 3/4” Wide by 141” Long Main HP 2 HP 220 volt 3 Phase Weight 1250 LBS

General Manufacturing 10" Table Saw - Model 350, 3 HP, 1 Phase, 208/230V, 60Hz, 13.7 Amp with dust collector hookup. Comes with a Biesemeyer fence and extension legs, 2 Craftsman miter gauges, a blade guard and 2 inserts.

The photos will show a lot. Works well. Has an essentially unused INKRA fence (LS32 positioning system), and INCRA Mast-R-Lift-II Router Lift and, including the router.

JET 708115K JWBS-14CS 14-Inch 1 Horsepower Woodworking Bandsaw with Graphite Guide Blocks, 115/230-Volt 1 Phase - MOBILE BASE INCLUDED LOOK BELOW FOR MY OTHER JET WOODWORKING MACHINERY!!!!!!!!

This is a 1 year old woodmaster planer and molder that has 50 hours on it. Comes with the molding kit 2 routers, drum sander, and excessory bar for making moldings and trim. It runs off single phase and comes with 2 set of flooring knives.