3 phase table saw for sale, brand-new and used.

You are buying today 1 used Robbins & Myers 3 PH 2 HP re-connectable motor 208/220 or 440V electric motor. This motor was replaced on a Powermatic 66 table saw with a single phase motor. 220V amp draw 5.4, 208V amp draw 5.8, 440V draw 2.7.

This is a DoAll Vertical Band Saw Model 1612-0 Serial No.209-63279 Year 1963 220/440 Volt 3 Phase 60 Cycle, wired for 220 Volt 3 PhaseMaximum Throat Depth 16", Maximum Work Height 12"Blade Length 122", Blade Width Range 1/16" - 3/4"Drive Motor 1-1/2 HP, Wheel Diameter 16"Air Pump for blowing chips2-Speed Transmission and Variable SpeedSpeed Range 50-5200 FPMApprox. Low Range 50-800, Approx. High Range 800-5200Approx.

NORTHFIELD MODEL 4 16" SLIDING TABLE SAW, 5HP, 3 Phase, in EXCELLENT condition from professional school. This is one of the best ones you will find! Has "Short Stop" electronic brake and controls, fences and miter gauges.

Rockwell Unisaw Table Saw 3 Phase. 220V

Delta Bullet motor from a 1950s Unisaw. I have not run it in a while, but worked last time it was hooked up. Axle spines freely. 

Hercules S330/2 STANDARD SPARTAN MODEL Hercules S330/2 SWIVEL HEAD, HIGH SPEED, HORIZONTAL, METAL CUTTING BANDSAW WITH 3 H.P., AND 60 DEGREE MITER CUTTING. Capacity @ 90°: 12” H x 18” W Rectangle (300 x 460 mm), 13” Round (330mm) Capacity @ 45°: 11” H x 12” W Rectangle (280 x 300 mm), 13” Round (330mm)

Dayton vertical Band Saw model 1FYX1 Used for about one hour so it is in new condition. Retailed new for $644. Asking only $250 Item Vertical Band Saw Cutting Capacity Rectangle14" x 6-1/4" Cutting Capacity Round6-1/4" Cutting Capacity Square6-1/4" Voltage115/230 HP3/4 Speeds2000/2800 fpm Max.

<img src="http://ti2.auctiva

BW 8233 DOALL #26-3 26" VERTICAL BAND SAW EQUIPPED WITH: -- SERIAL: 55-57501 -- 440V/3 PHASE

Present your best items with Auctiva's FREE Scrolling G

This listing is for a Cantek 18" Upcut Saw. Specifications: Uses an 18" Blade Model No: CFS-18R 10 HP Total Amp: 26 Serial No: 070031109 Brand new hoses and spool valve 3 Phase Wired for 480 volts 10'2" x 30" x 55" The table is 41" tall.

For sale is a Everett Industrial Metal Circular Chop Saw 8" Diameter Disc 220 3 Phase. Comes with a Baldor Motor. Runs good.

This is a nice sliding panel saw. It does require 480vac 3 phase power to run this piece of equipment. Very reliable piece of equipment and does run very well.

Turnpro 7" x 12" Horizontal 3 Speed Geared Head Band Saw Hydraulic Down Feed Coolant System 1 Hp / 220 Volts / Single Phase

Westinghouse 3/4 HP Electric Motor With Pulley 1725 RPM --Cycle 60 - Volts 115 - Amps 115 - Phase 1 - Deg C 55 - Hours Cont. Three inches between centers for motor mounting on bottom. This Came off my small vintage Crastsman table saw, works great I just needed a larger motor.

Oliver 270D. 5hp table saw. T Type fence is 52 inch.

KASTO 15-3/4” (400mm) High Production Semi-Automatic Cold Saw- Used - AM15594 Model: GKS 400 U

KASTO 15-3/4” (400mm) High Production Semi-Automatic Cold Saw - Used - AM15593 Model: GKS 400 U Serial: 3110 105 026

TABOR Abrasive Foundry Saw — Used — AM15799 Model: CR40.2.26V4SP Serial: 80M.2626