3/8 i bolt for sale, brand-new and used.

Free U.S. Shipping!

I now have over 2400 items for sale! Thanks everyone! Free U.S.

Up for bids is a slotted angle iron shear from the leader of shears and cutters, H.K. Porter. Here are the specs on it: Item: Slotted Angle Cutter Model 2790 Function: To Cut Predrilled and Slotted Angle up to 3" Wide, 11/2" Deep, Maximum Thickness of 1/8" Characteristics: Lightweight, Portable Handle Length (In.): 38 Total Length (In): 45 Weight: 18 Lbs Width (In): 9.5 A must have tool for electricians, carpenters, plumbers, contractors.

Equipment From A 113,000sq ft Fulfilment Center Our Company Has Purchased The Equipment In This Fulfilment Center. The item(s) listed can be viewed onsite in its running condition after Octobor 17th 2014 The equipmented listed here will not be ready for sippment till after Oct 17th. If you are in need of a up and running Fulfil

CARGO SEALS (TANKER) CABLE LOCK SECURITY SEALS - ALL METAL. TEN GREEN SEALS. A TOTAL OF TEN FACTORY-NEW

I am selling a Series 400 Adapter Flange/UNi Flange for Ductile Iron Pipe (UFA400-C-3) 3"/ 150 WP Set Screws --5/8" x 1-1/4" Bolt Hole--7/8"

LOT OF 8MECHANICAL PLUMBING TEST PLUGSMADE BY CHERME AND IPS CORPORATION7PCS, ARE FROM CHERME AND 1 PC. FROM IPS CORPORATIONYOU GET 8 PLUGS 2 PLUGS ARE 4 INCH3 PLUGS ARE 3 INCH3 PLUGS ARE 2 INCHSHOULD BE ENOUGH TO TEST YOUR PLUMBING LINES IN ONE REGULAR SIZED HOUSEMISSING ONE BOLT AND WING NUT ON THAT 4 INCH PLUGSOME OF THE WING NUTS ARE MIS

Josam Plum

11" CAST IRON WATER SHUT OFF VALVE WHEEL This is a great old industrial piece that has been painted over several times, I see rust, I see red and on the top is blue. Size is 11" across and square bolt hole is around 5/8". Nice piece, that you may want to remove the paint or put a clear coat over to preserve the look.

You are buying a Brand New 3/4" NPT Male X 3/4" NPT Female Brass Ball Valve Rated 400 PSI Rated for NG service as well as water and other liquids and gasses. Save $$$ here on a hard to find item. Great price, so you better get it quick!!!!

I have two of these pumps for sale. Below I have included all the relevant information that you will need to determine if this is the pump you need. Please see information below on how to locate pump in Google using PDF.

Concentric gear pump bought from Grainger earlier this year. It worked fine but for my application I needed a piston pump. It did get pretty warm once and was leaking some out of the front seal.

In 1955, when I was 15 and building a “quarter-size racer”, I bought this amazing device from one of the great war surplus houses of the time, probably in Nebraska or Kansas. But never installed it or ran it under serious power. It is a single dense greenish cube transmission weighing about 18 lbs, and 7 to 8 inches a side.

The pump is of the canned rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid.

Up for auction is a new Vickers Eaton cast iron foot mount/bracket. It will support many hydraulic pumps other than Vickers or Eaton. Please refer to the pictures and dimensions listed.

This auction is for (1) gear pump. It is a new pump but a discontinued Webster model. I can't find many specifics on it but I believe it is approximately 1.5 gpm at 1725 and probably rated for 2500 psi.