3/8 square drive for sale, brand-new and used.

Super set includes the following: -Hinged handle, 3/8" square drive

Super set includes the following: -Handle, ratchet, 1/2" drive

THIS IS A USED BLUE POINT BY OTC Six-lug spanner-type wrenches remove and install rear wheel bearing locknuts They're built for use with a 3/4 inch square-drive ratchet or breaker bar Socket O.D. is 3-5/8 inch Designed for servicing Chevrolet and GMC 15,000 lb axles 17,000 lb 2-spd axles and 15,000 lb trailing axles

The Lotoons Store NEW OTC 6111 T55 Torx 3/8" Square Drive Socket

The Lotoons Store NEW Wright Tool 3403 3" Extension 3/8" Drive

The Lotoons Store NEW Wiha 77146 Hex 1/4-Inch Drive Bit Socket 6-Inch Long 5.0mm

This Proto Professional 1 7/8" Impact Socket that has been customized to a extension of 9". The 1 7/8" socket is welded on to a 10" 1" drive extension. 1" Drive size 6-Point Concentric openings Large clearance holes Tight nut end tolerances Made from high alloy steel for greater strength Specially heat treated for the correct balance of strength and durability Technical Specs ItemImpact Socket Drive Size1" Number of Points6 Socket Depth Deep

Geffen - Best deals on eBay NEW Martin STM1227 27mm Type III Opening 1/2" Square Drive Socket 12 Points Standard 1-3/4" Overall Length Chrome Finish

This tool retails for $410.00 It is in new condtion and the only marks on it are where the writing bled through the calibration certification sticker that was located near the head of the ratchet . Cementex 300200TW38i High Voltage Double-Insulated Torque Wrench is tested to 10,000 volts and rated for use up to 1000 volts AC and 1500 volts DC.

Snap-On L72T Torque Wrench Ratchet 3/4" Drive 400 LB/FT w/Handle / Case / and extra SNAP-ON 24B handle/bar. The new list price for these start over $800 and go up from there - and this one is barely used. Serial # 3557.

Drive adaptor fits Ridgid 700 pipe machine. It is a nominal 3/4" square drive opening. Actual size is 7/8" i.d.

This auction is for an original 1 1/2 HP IHC McCormick Deering gas engine magneto drive gear for the spark plug fired Bosch FX1 magneto It measures approx. 2 3/4" in diameter, and has 30 teeth with a tapered hole to mount on the Bosch FX1 high tension magneto for spark plug fired engines. It is in nice condition with its teeth still very square and not razored, but does have some minor crazing, as all of these original gears have.

This auction is for a nice original Fairbanks Morse 3 Hp ZC enclosed crankcase gas engine magneto drive gear. It  measures approx. 2 3/4" in diameter, and has 25 teeth with a tapered hole to mount on the Fairbanks R, J, or X 1 cylinder high tension magneto for spark plug fired engines.

This auction is for a nice original Fairbanks Morse 6 HP Z gas engine magneto drive gear. It has a part number of ZC142 on it, and measures approx. 3 1/2" in diameter, and has 32 teeth with a 3/8" hole to mount on the Sumter low tension magneto for igniter fired open crank case engines.

This auction is for a nice original Fairbanks Morse Headless gas engine magneto drive gear. It has a part number of DJ142 on it, and measures approx. 3 1/4" in diameter, and has 30 teeth with a 3/8" hole to mount on the Sumter #12 low tension magneto for igniter fired engines.

This auction is for a nice original 1 HP IHC Mogul gas engine magneto drive gear. It has a part number of 1879T on it, and measures approx. 3 1/2" in diameter, and has 32 teeth with a 3/8" hole to mount on the IHC or Accurate Engineering R low tension magneto for igniter fired engines.

This auction is for a nice original 3 HP IHC McCormick Deering gas engine magneto drive gear. It has a part number of 9779T on it, and measures approx. 3 1/4" in diameter, and has 36 teeth with a 3/8" hole to mount on the IHC L low tension magneto for igniter fired engines.

This auction is for a nice original 1 1/2 HP IHC McCormick Deering gas engine magneto drive gear. It has a part number of 9679T on it, and measures approx. 2 3/4" in diameter, and has 30 teeth with a 3/8" hole to mount on L IHC low tension magneto for igniter fired engines.