AD9850 0~55MHz DDS Signal Generator For HAM Radio VFO SSB RIT 6 Bands, US $6300 – Picture 0

AD9850 0~55MHz DDS Signal Generator For HAM Radio VFO SSB RIT 6 Bands, US $6300 – Picture 1

AD9850 0~55MHz DDS Signal Generator For HAM Radio VFO SSB RIT 6 Bands, US $6300 – Picture 2

AD9850 0~55MHz DDS Signal Generator For HAM Radio VFO SSB RIT 6 Bands, US $6300 – Picture 3

AD9850 0~55MHz DDS Signal Generator For HAM Radio VFO SSB RIT 6 Bands, US $6300 – Picture 4

AD9850 0~55MHz DDS Signal Generator For HAM Radio VFO SSB RIT 6 Bands, US $6300 – Picture 5

Ad9850 0~55mhz Dds Signal Generator For Ham Radio Vfo Ssb Rit 6 Bands

US $6300

Shen Zhen, China
Jan 29th

Open on mobile:
QR code

AD9850 0~55MHz DDS Signal Generator For HAM Radio VFO SSB RIT 6 Bands 0~55MHz DDS Signal Generator For HAM Radio VFO SSB RIT 6 Bands Description: This is a 0~55MHz (latest version, firmware updated in 2013) DDS Signal Generator. It is based on AD9850 chip and is very easy to operate. Supports 0~55MHz continual adjust at 1Hz step. This generator has 78L05 voltage regulate. Input current at 200MA, input voltage 8-9V would be the ideal voltage. Input voltage of 12V can only be used for short time testing, otherwise will cause heat to board. 5p/6p connect to encoder as per photo. 7p of the middle connects to digital matrix input. 14p (8V GND) is 8V power supply from main board. If powered by main board, DDS does not need independent power supply. 1~6 correspond to 6 frequency bands: (3.8,7 ,9,14,18 or 21,27 or 29) ISB, USB, CW are the three mode choices. DT is signal from main board Keys & Connection interfaces: ENC: encoder switch MEM: switch for memory mode VFO: Transfer from VFO A to VFO B, or from VFO B to VFO A. SSB: Working mode change: circulate from USB, LSB, AM, CW, and on and on... RIT: fine tuning to receiving frequency CAL: set functions KB-1 and KB-2 have common shared pin, but is not GND. How to operate: Press CAL, power on, then we enter setting screen. Let go/release CAL. A: ENABLE 6XREFCLE: setting chip clock mode, adjust frequency encoding setting. AD9851 set to 6-multiply frequency, AD9850 set to 1multiply frequency. Press CAL then quickly release to enter next step B. B: DDS-SYSTEM-CLK: Chip working frequency setting. Use encoder switch to adjust value. Operate in accordance with STEP key. AD9851 set at oscillator 6-multiply channel, AD9850 set at actual output of oscillator. Press CAL then quickly release to enter step C. C: MIN_RX_DDS_FREQ:Setting minimum working frequency. Use encoder switch to adjust value and in accordance with STEP key. Press CAL then quickly release to enter step D. D: MAX_RX_DDS_FREQ:Setting maximum working frequency. Use encoder switch to adjust value and in accordance with STEP key. (Smaller than 60MHz would be OK ). Press CAL then quickly release to enter step E. E: SSB_OFFSET:Fine tuning for SSB working mode. Use encoder switch to adjust value and in accordance with STEP key. Press CAL then quickly release to enter step F. F: CW_OFFSET:Fine tuning for CW working mode. Use encoder switch to adjust value and in accordance with STEP key. Press CAL then quickly release to enter step G. G: OFFSET_FREQ:Setting of offset Frequency. e.g, set to 9MHz or 10.7MHz, use encoder switch to adjust value and in accordance with STEP key. Press CAL then quickly release to enter step H. H: MULTIPLIER: multiply setting for frequency. Should be set as 1, press CAL then quickly release to enter step I: I: Screen displayes word "SAVE", automatically save the above setting, and returns to normal working. Notes: 1. DDS SYSTEM CLK: can use frequency tester to get 30MHz oscillator, multiply the tested value at 6, then put the multiplied value here. If using AD9851, make initial setting at 180000000. 2. OFFSET FREQ: can be set as + or - . Rotate encoder switch to change value, press STEP key, then rotate encoder switch to adjust step. Minimum working frequency plus (+) offset frequency should be high than 0 (zero). Frequency display: RX = MULTIPLIER x (RX_DDS_FREQ + OFFSET_FREQ) TX = MULTIPLIER x (RX_DDS_FREQ + OFFSET_FREQ + TX_OFFSET_FREQ) The frequency programmed into the DDS, is calculated as shown below. RX = ABS(RX_DDS_FREQ) TX = ABS(RX_DDS_FREQ + TX_OFFSET_FREQ) RX_DDS_FREQ, MIN_RX_DDS_FREQ, MAX_RX_DDS_FREQ, TX_OFFSET_FREQ & OFFSET_FREQ Examples: 1. DDS output range 30~40MHz: MIN_RX_DDS_FREQ MAX_RX_DDS_FREQ OFFSET_FREQ RX Frequency display range. 30 MHZ 40 MHz 100 MHz = 130 MHz to 140 MHz. \ Note 1 30 MHZ 40 MHz -10 MHz = 20 MHz to 30 MHz. / -40 MHZ -30 MHz 170 MHz = 140 MHz to 130 MHz. \ Note 2 -40 MHZ -30 MHz 60 MHz = 30 MHz to 20 MHz. / 2. setting FT180A with DDS: ENABLE RPT NO X6 RECLK X6 DDS SYSTEM CLK 180M MAX DDS FREQ 65M MIN RX DDS FREQ 10.701M (Offset frequency + RIT frequency) MAX RX DDS FREQ 60M TX OFFSET FREQ 0 MAX RIT OFFSET 1K (RIT frequency) OFFSET FREQ -10.700M -(Offset frequency) MULTIPLIER 1 Our Working Time is as below (GMT+8): 9:30AM -- 6:00PM (Monday to Friday) Please allow us at least 24 hours to reply you when in the office, thanks! Shipping If you intend to bid for more than 1 item, then we can ship them together. The total shipping fee will be the sum of individual shipping fees. There is no further discount. We only ship to ebay registered address. So please be assure your address in ebay is Correct and Valid. Item will be shipped within 24 hours on payment received from Hong Kong using Airmail. Delivery time depends on destination and other factors, it may takes up to 30 business days. Optionally, Express Shipments with tracking service via EMS/DHL/UPS with a quoted delivery time of 5 to 7 business days is also available Here is the estimated time for your reference only: The delivery time may vary due to public holidays, countries, and customs etc. Thanks for your understanding! We ship item promptly and please rate us 5 star on shipping time according to ebay rules. http://pages.ebay.com/help/feedback/detailed-seller-ratings.html Feedback The delivery time may vary due to public holidays, countries, and customs etc. Thanks for your understanding! If you are considering giving a neutral or negative or a low DSR(4 star or below), do write to us and give us an opportunity to address your concerns first. We are always stand-by to help for any questions or concerns. Positive feedback is automatically left for you after you left to us positive feedback. Return Returns: We stand behind every product we sell. If you're not pleased with your purchase, please kindly contact our customer service representatives via email or ebay "Contact seller" for an authorized RMA number. Your returned product(s) will not be processed without a RMA. Buyer is responsible for return costs. Payment PayPal payment only. Any VAT or TAX are not counted. If buyer required to cancel bid for their mistake or any other personal reasons, 5% of the total price is charged for relisting and restocking fee. We didn't ship to Africa, Italy, China,HongKong, Macau,Taiwan due to cross-border express delivery and customs issue ,pls understand and pay your attention to it before bidding or buying. On Sep-21-14 at 18:25:16 PDT, seller added the following information: