bolt shaft for sale, brand-new and used.

Antique Vintage Fairbanks Cast Iron Industrial Caster Cart Table Wheel 4 bolt 5 x 7 CI base -- with grease fitting - 6" CI wheel with bearing & oil hole -- swivel base ball bearing .. all original except the nut & lock washers that were missing that I used to secure wheel shaft. good used condition -- no breaks or repairs--- works fine.

TOTALLY REFURBISHED VINTAGE DELTA UNISAW FENCE. This is an early Delta table saw fence that fits all UNISAW's with the 1.375" diameter rails. This is the premium Delta Unisaw fence, with the cam locking ball ended lever and the knurled finger knob for tightening the rear clamp block.

Here is a rope pull start recoil assembly for a Briggs & Stratton model 12H802 Type 1764-E1 vertical shaft lawn mower engine. This pull starter has four 3/16" mounting bolt holes that are about 4-1/2" on center. There is a 2" round center button that has two drive tangs.

Hydraulic Pump Brand: Harsh International Parker 2100 Series Gear Housing (577-00661-15) MPN: 103054

Canadian Ground Shipments by Purolator

inc

i

HUMBOLDT CBR MECHANICAL LOADING PRESS CONCRETE SAMPLES LABORATORY TESTING EQUIPMENT THIS PIECE OF EQUIPMENT RETAILS FOR A BASE PRICE OF $2220.00 PLUS SHIPPING. I HAVE A BUY IT NOW OF

CASAPPA TRIPLE PUMP(Three sections) 1.27/1.27/.29 CU/REV 13 TOOTH SPLINE SHAFT CCW ROTATION. SAE-B 2 Bolt Flange.

CRS V20 VANE PUMP Brand new, CRS hydraulic balanced vane pumps. Cast iron construction. Operating rotation can be field reversed.

Used in working condition12V DC Motor Double Shaft2.7 Amp4500 RPM7.5 oz/in TorquePrimary Shaft dim. 5mm x 15mm smoothSecondary Shaft dim. 5mm x 13.5mm smoothMotor Body dim.

Used Talboys Model 134-1 Heavy Duty Overhead Mixer Part # 134-1 Top mounted Standard Speed Control

Motor Type: Shaded Pole RPM: 1550/900 HP: 1/50 Volts: 115 Amps: 1.2/.7 Hz: 60 Phase: Single Phase

Ecolab / Ace Pump Corp water pump model ECL-10, ECL-9, serial number 36557. Outlet measures 1 1/8 inches to the inside of the threads, inlet measures 1 1/2 inches to the inside of the thread -- I'm not sure if this is the right way to measure it, but I think you can figure it out. Shaft size is 5/8 of an inch and the flange bolt holes measure 4 1/8 inches center to center, in both directions.

--------------------------------------------------------------- **** Special limited stock sale pricing **** ----------------------------------------------------------------

This listing is for a used Talboys 102 Light Duty Stirrer Mixer. It is far from brand new, but still an effective mixer and extremely reliable. With the controller on here, it looks like it can rotate smoothly as low as 20RPM, and probably a top RPM of maybe 200-300.

var arICImages7 = new Array(6); arICImages7[0]='http://d3d71ba2asa5oz.cloudfront.net/82000055/images/k36e009-1.jpg'; arICImages7[1]='http://d3d71ba2asa5oz.cloudfront.net/82000055/images/k36e009-2.jpg

Plans to build the 4-In-1 Vacuum Engine The correct terminology is "atmospheric engine". Never the less, here is a "flame eater" engine you can build any of four ways: (1) - Air Cooled Side Crank as shown, (2) - Water Cooled Side Crank, (3) - Air Cooled Center Crank or (4) - Water Cooled Center Crank! The air cooled engines have an optional belt driven cooling fan which provides cooling for long running sessions.

Product Information Item Name: Eaton 109-1101-006 Hydraulic Motor Pump