bolt sleeve for sale, brand-new and used.

Technical Specs Item Unit Bearing Motor Motor Application HVAC/R Motor Sub Application Refrigerator/Freezer Motor Type Shaded Pole Enclosure Totally Enclosed Air-Over HP 1/125 Nameplate RPM 1550 Frame Nonstandard

Item Condenser Fan Motor Motor Type Permanent Split Capacitor Enclosure Open Air-Over HP

double shaft Direct Drive blower motor 1/6 HP 208-230 VOLTS 60/50 HZ 1 AMP 3 SPEEDS 1075 RPM SLEEVE BEARING COUNTER CLOCKWISE ROTATION OPEN ENCLOSURE EXT THRU BOLT MOUNT OVERLOAD PROTECTED 7 1/2" X 1/2" X 8 1/2" SHAFT

New in the Unopened Box 5 5/8 Direct Drive 3 Ring Blower Motor Mounting Kit Including Hardware The Package Contains as follows. 1-Motor Support 3-Grommet Centers 3-Grommet Rings 3-Sleeve Spacers 3=Type B Sheet Metal Screws & Lock Washers 1-5/16 X 1 3/4 Inch Long Clamping Bolt & Nut Each Box has the Instructions on how to use the mounting kit properly. Some boxes are discolored, faded, scraped, or worn.

PROTECH Furnace Motor - 1/6 to 1/2 hp 120/1/60 (1075 rpm/4 speed) 51-23012-41 Technical Data: HP: 1/6 - 1/2 No. of Speeds: 4 High Speed (RPM): 1075 Input Voltage (V): 120 No. of Phases: 1 Frequency (Hz): 60 Rotation Direction (OSE): Reversible Run Capacitor (uF/V): 5/370, 7.5/370, or 10/370 FLA at 120V (A): 7.30 Shaft Diameter (in.): 1/2 Motor Body Diameter (in.): 5-5/8 Keyed/Flat Shaft Length (in.)

Fasco D1044 OEM Replacement Motor OEM Replacement for IEC 5KCP29DK8387S, S89210 Motor Type: Permanent Split Capacitor RPM: 970 HP: 1/4 Volts: 115 Amps: 6 Hz: 60 Phase: Single Phase Thermal Protection: Automatic Speeds: 3 Rotation: CW Shaft End Bearings: Sleeve Frame Size: 5" Frame Motor Diameter (In.): 5 Motor Length (In.): 4 1/3 Shaft (In.):

Fasco D1045 OEM Replacement Motor Motor Type: Permanent Split Capacitor RPM: 1100 HP: 1/30 Volts: 115-127 Amps: 0.53 Hz: 60 Phase: Single Phase Thermal Protection: Automatic Speeds: 3 Rotation: CW Shaft End Bearings: Sleeve Frame Size: 5" Frame Motor Diameter (In.): 5 Motor Length (In.): 3 1/8 Shaft (In.): 1/2 X 9 Bolt Circle (In.): 4-5/8 (4.62) OEM Replacement for IEC 5KCP29BK8382S,

For sale is a new in unopened box Fasco D 158 HVAC Blower motor. Cross Reference Numbers-S88-233D158M39106119-0803-12 Description: Thermally protected, rotation CWSE, sleeve bearing A: 3-7/8"; Agency Certification: UR/CSA; Ambient Operating Temp.

Technical Specs Item Unit Bearing Motor Motor Application HVAC/R Motor Sub Application Refrigerator/Freezer Motor Type Shaded Pole Enclosure Totally Enclosed Air-Over HP 1/83 Nameplate RPM 1550 Frame Nonstandard

Century 325P267 1725RPM 1/8 HP 115V AC Water Circulator Motor 4UE22 OBG2004 Comes with Everything See In the Picture BRAND NEW! FREE DOMESTIC SHIPPING! OBG2004 - 4UE22 - Motor, 1/8 HP, Circpump - Circulator Pump Motor, Split Phase, Open Dripproof Enclosure, 1/8 HP, 1725 RPM, 115 Volts, 3.1 Full Load Amps, 60 Hz, Service Factor 1.00, 48Y NEMA Frame, Bracket Mounting, Sleeve

Hydraulic Cross Slow 5.2 Motor for Wall Saw CROSS HIGH SPEED HYDRAULIC MOTOR Brand new, Cross hydraulic gear motor. Model 50MH52DBCSC. Pressure balanced loading plates for high efficiency.

Genuine U.S. Military Issue Surplus   Facet Enterprises, Inc. - Fluid Filter Element Assembly - P/N:  639632 P/N:  639632 This item cross-references to the following....

Two Yard Steel Self Dumping Bin Better Built Bins! Tops in the Industry! 2 Yd Bin to hold

These 2 wheels are off of my gate. There are no bearings and the bearings and king pin sleeve are just to show what is needed to make a complete working wheel. NO BEARINGS  

Sottof Sales In working condition, not sure what brand they fit. 1 1/4" Dia. hex end is 1" L the other end is 7/8" L, the hole is 17/32" dia for a 1/2" -13 bolt, the hex openening is 7/8" across the flats.

Sottof Sales In working condition, not sure what brand they fit. 1 1/4" Dia. hex end is 1" L the other end is 7/8" L, the hole is 17/32" dia for a 1/2" -13 bolt, the hex openening is 7/8" across the flats.

Sottof Sales In working condition, not sure what brand they fit. 1 1/4" Dia. hex end is 1" L the other end is 7/8" L, the hole is 17/32" dia for a 1/2" -13 bolt, the hex openening is 7/8" across the flats.

Contact Wheel & Flat Platen “D-D Work Rest” for Bader II & III Knife Maker Belt Grinders Work Rest Includes: -Work Rest for Contact Wheel and Flat Platen with 2-3/8” x 1/2” cuto

Total System “D-D Work Rest” for Wilton & Jet Square Wheel Knife Maker Belt Grinders Work Rest Total System Includes: -Large Work Rest for Contact Wheel / Flat Platen with a 2-3/4” x 1/2” cutout to wrap around the belt

Total System “D-D Work Rest” for Bader I, II and III Knife Maker Belt Grinders Work Rest Total System Includes: - Work Rest for Small wheel holder