dirt paint for sale, brand-new and used.

OK,THIS GREAT FLAME KIT IS VERY VERSITALE. AS PICTURES SHOW, YOU CAN USE IT TO FLAME WEEDS, BURN HEAVY WEEDS, DRY OR THAW SAND, DIRT, WATER PIPES; HEAT METAL CASTINGS, PIPES AND TUBING; STERALIZE BIRD AND ANIMAL CAGES; REMOVE PAINT AND GREASE, OIL AND MUCH MORE. WHAT IS PICTURED IS ALL THERE IS SO LOOK CLOSLEY TO MAKE SURE YOU KNOW WHAT YOU ARE BIDDING ON.

VINTAGE 1940 INSTRUCTION MANUALFOR... FARMALL TRACTOR CULTIVATORS MODEL NOS. A-134 AND A-435DISCOLORED FROM AGE...

This Auction is for a Set of Two (2) Wire Brushes This is a Quality Wire Wheel Brush. Not one of the cheaper ones that "fly apart" on you. 7" (175mm)Wire Wheel Brush Removes rust, paint and

This is a RIDGID (1/8 to 2" Pipe - 1/4" to 2" Bolt) Universal Threading Die Head. This die head is in okay used condition with some normal cosmetic signs of use including scuffs, chipping of the paint, dirt, grease, etc. Teeth on die look is very good condition.

Lab Line Instruments 2053 Multi-Blok Heater - 200W Please refer closely to all the photos before purchasing. Used. Lab Line Instruments 2053 Multi-Blok Heater 120VAC 50/60Hz @ 1.67A 200W 8 3/4" x

This listing is for a PROTEK Signal Generator model "B-813". The device has not been tested. Does not have adapter cord.

nice bender015-11-04-20-513 PLEASE READ BEFORE BIDDING: SHIPPING IS NOT FREE UNLESS THE LISTING SAYS FREE SHIPPING UNDER THE PRICE WHERE IT SAYS “SHIPPING:” THE SHIPPING CHARGE IS FOR SHIPPING HANDLING PACKAGING AND GETTING YOUR PARCEL TO THE CARRIER. Make your decision to buy based on the total cost of the item including shipping No adjustments after purchase

very nice ridgid 506 bender, cost was over $200015-11-02-20-513 PLEASE READ BEFORE BIDDING: SHIPPING IS NOT FREE UNLESS THE LISTING SAYS FREE SHIPPING UNDER THE PRICE WHERE IT SAYS “SHIPPING:” THE SHIPPING CHARGE IS FOR SHIPPING HANDLING PACKAGING AND GETTING YOUR PARCEL TO THE CARRIER. Make your decision to buy based on the total cost of the item including shippi

super nice bender. note the 5/8 bender is complete. to use the 7/8 bender you will need to swap the center pivot pin (intended to be removable and pulls out by hand to release the tube after it is formed) and swap the drive handle/pinion with the other one, which also just pulls out with no tools.

This auction is for the Heavy Cast Alloy & Steel Miter Gauge as pictured from a vintage Shopsmith Multi-Function 10-E Woodworking Machine Serial # ER-9646 It is about 15" Long overall..the head @ 5 3/4" wide..the rail is 1/4" X 3/4" Wear and Tear Dust and dirt rust and pitting nicks paint loss but in good working condition. Local Pick-up Available Some items will be disassembled for safe, economical shipping. I will combine shipping on multiple purchases when practical.

This auction is for the Heavy Cast Alloy & Steel Rip Fence as pictured from a vintage Shopsmith Multi-Function 10-E Woodworking Machine Serial # ER-9646 It is about 22"" Long overall..the head @ 3 1/2" wide..the internal measurement is 18" Wear and Tear Dust and dirt rust and pitting nicks paint loss but in good working condition. Local Pick-up Available Some items will be disassembled for safe, economical shipping. I will combine shipping on multiple purchases when practical.

This auction is for the Alloy Gauge Collar as pictured from a vintage Shopsmith Multi-Function 10-E Woodworking Machine Serial # ER-9646 Mounts with 2 set screws. About 3 5/8" Long Wear and Tear Dust and dirt rust and pitting nicks paint loss but in good working condition. Local Pick-up Available Some items will be disassembled for safe, economical shipping.

This is a nice strong running Dual Shaft A.C. Motor from a vintage Sears Craftsman 12" Wood Lathe Model # 149-23871 with twin 1" diameter tubular bed rails 1/2 Horsepower 1725 RPM 60 HZ 1 phase 115 Volt 8.4 amp reversible wired right handed Clockwise on 5/8" (right) shaft as you face the nameplate. Comes with mounting bracket and clips...key and spindle cover as pictured.

This is great to protect your floors from paint, dirt or other staining substances. Unopened. Buy now.

Scaffold Caster Wheel We do not know what brand, style, model, etc. Comes AS IS!!! All sales FINAL!!!

Athol 614 Vise Fixed Base 4 Inch Jaws Heavy Vintage Vice Up for sale is my Athol 614 vise. I got this vise at a farm auction a few years ago, and have used it as my main vise. I recently replaced it with a Wilton bullet, so I am passing it on.

Used metal card file,with stickers. Opens and closes. Slight rust, dirt, missing paint, and other signs of use and wear.