Eco-Etch Pro Concrete Etch & Clean Concentrate - 1 Gallon New and Improved Formula! Better. Safer. Faster. Eco-Etch Protm is a water-based non-hazardous, non-corrosive, biodegradable concentrate concrete etch and cleaning solution. It is the ideal acid etch alternative. This advanced formula incorporates a custom blend of surfactants, organic minerals and derivatives of a plant based extract for the most effective concrete etching solution available. It does not contain phosphoric, hydrochloric or muriatic acid, yet works better, safer and faster. Eco-Etch Protm is the preferred eco-friendly and user friendly acid etching alternative for interior or exterior surface preparation applications. It will not burn skin, corrode metals, or harm vegetation. Clean and etch concrete, masonry, cinder block, brick, mortar joints and grout to properly prepare substrates for optimum penetration and adhesion of stains, paints, industrial coatings, and sealers. Eco-Etch Protm also removes dirt, clay, mortar deposits, rust and efflorescence. A one step concrete etch and clean solution that brings back a new look surface. Highly recommended for use with SoyCrete Concrete Stain and Eco-Tuff Coatings for optimum porosity and desirable results. Eco-Etch Protm begins to work immediately upon contact without toxic hazards or dangerous skin burns associated with traditional acid formulas. Eco-Etch Pro should be used in full strength or diluted up to 3:1 (makes up to 4 gallons) with water for lighter cleaning and etching requirements. One gallon will cover up to 250 square feet. Dwell time will vary from 1 to 15 minutes which is also affected by the dilution ratio, porosity, and temperature. Rinsing thoroughly with water neutralizes the etching action. Features Plant Based Biodegradable Non Corrosive Will Not Burn Skin Will Not Harm Vegetation No Toxic Vapors Neutralizes Easily With Only Water Great Paint & Coating Preparation For: Concrete Tilt-Up, Pre-Cast Concrete, Concrete Floors, Stucco, Masonry Block and more. Or Use for Heavy Duty Cleaning to Remove: Efflorescence, Rust, Ground-in Dirt, and more. Technical Specs VOC: 0 g/l Odor: Very Mild. Sweet. Appearance: Clear Freezing Point: 32°F Dwell Time: 1-15 Minutes Shelf Life: 12 Months APPLICATION: Ensure that all adjacent surfaces not to be etched are appropriately protected. All areas to be etched must be clean, dry and free of sealers, coatings, oils, grease, or other foreign contaminants. Test Area: Always prepare a test patch prior to full application. This will indicate the optimum dwell time, dilution and substrate compatibility required for successful project completion. Use in concentrate form for more aggressive etching or to minimize contact time. Dilute up to 3 parts water to 1 part concentrate depending on level of cleaning and etching desired. The longer the contact time, the more penetration of etch. Etching will continue for as long as the material remains wet on the surface and prior to neutralizing. Apply by pouring material directly to the surface or by garden-type pump sprayer. Spread out material if necessary to ensure uniform coverage by using brooms or brushes. Work in controllable areas depending on temperature and environmental conditions to avoid premature drying of material. Best results are achieved at temperatures above 40°F and below 95°F. Warmer temperatures will accelerate drying that may require working in smaller areas or constant re-applications to keep the material wet during the determined contact time. Pre-spraying area with water to cool hot surfaces for best results. Do not allow material to dry before rinsing. Etching will begin immediately as witnessed by a mild foaming action. If foaming is not present, a barrier or incompatibility exists between the material and the substrate. Such barriers must be removed prior to proceeding. Allow 1-15 minutes contact time as determined by your test patch. Add mottling effects by varying contact times. Neutralizing/Cleaning: For small areas, simply rinse area thoroughly with clean water, then wipe clean with dry lint free cloth. For larger surfaces, rinse liberally with clean water applied by garden-type pump sprayer or hose. Use a hard bristle brush or floor buffer with medium to coarse stripping pad. Extract all residue with a wet/dry vacuum. Repeat rinse if necessary to ensure all residue is removed. Outdoor applications may be best performed by rinsing thoroughly with a pressure washer. Staining/Coating/Sealing: As with any etching compound, it is advisable to check the pH of the substrate before applying a coating material to ensure that it is compatible with the new coating system being applied. Perform a final substrate test for adequate porosity prior to coating application. Spray areas lightly with water. If water absorbs within seconds, you have achieved good porosity. If water absorbs slowly or beads, re-evaluate your test procedure and reapply in the deficient area and repeat process. After sufficient drying time, ensure the surface is completely dry and dust free prior to coating installation in accordance with good painting practices and the coating manufacturer’s instructions. Follow all safety precautions on the product label and MSDS. Keep away from children. Check out the following links for further information: Eco-Etch Pro PDS Eco-Etch Pro Installation Guide Eco-Etch Pro MSDS Any further questions please feel free to contact me via ebay email or by phone at 231-878-6543.
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.
