Engines (Stationary Engines) for sale, page 175

Witte hit miss engine instruction manual no 20 and sawing outfits gas

Lostant, Illinois, United States
Jan 31st

New Reprint Manual. Instruction Book Witte Engines and Sawing Outfits No. 20.

Belt pulley drive belt ~7" x 44' hit & miss engine / john deere 28 pounds!

Mount Pleasant, Iowa, United States
Jan 31st

BELT PULLEY DRIVE BELT ~7" X 44' Hit & Miss Engine 28 Pounds! No splices, Save $ Nice Belt! Best Price Anywhere!

Early vintage salsbury 600 ?? gas engine hit n miss show

Mitchell, Nebraska, United States
Jan 31st

VINTAGE SALSBURY 600 ?? GAS ENGINE i was able to get it to pop off with a little starting fluid has spark carb needs cleaned out etc is missing the org clutch pulley system shipping high due its wt and box size

Early vintage salsbury 600 ?? gas engine parts engine hit n miss show

Mitchell, Nebraska, United States
Jan 31st

VINTAGE SALSBURY 600 ?? GAS ENGINE for parts etc it turns over about 60 % both ways but will not due a complete turn i think there must be rust on the cly i have no other tin work for it i do have the fuel tank that was off of it when i got it in a differnt auction and also a prety compete engine on ebay now also that should run this one is is missing the org clutch pulley system shipping high due its wt and box size

Early vintage salsbury 600 ?? gas engine fuel tank

Mitchell, Nebraska, United States
Jan 31st

VINTAGE SALSBURY 600 ?? GAS ENGINE fuel tank should clean up and be usable a little rust in side i do have a engine that this came off of of it when i got it in a differnt auction and also a pretty compete engine on ebay now also that should run this one is is missing the org clutch pulley system shipping high due its wt and box size

Stover upright gas engine mv2

Cumberland, Rhode Island, United States
Jan 31st

old antique Stover vertical gas engine made in Illinois, way back when. needs tlc to get running, engine turns freely but needs an oil ring, partially dissembled. has small crack in water tank and exhaust manifold see pic, missing spark plug and plug wire.

Cushman engine hit and miss with curtis air compressor on cart antique motor

Norman, Oklahoma, United States
Jan 31st

Nice looking Cushman engine attached to a Curtis air compressor of the same era. I believe this was built around the mid 1920's. The engine has the original magneto with an impulse and automatic advance.

Original briggs & stratton gas engine model wm wmb kick offset starting pedal !!

Baldwin, Wisconsin, United States
Jan 31st

This is an Offset Starter Pedal & Hardware For Briggs & Stratton Gas Engines... This is Off A WMB I parted Out, I think It fits the Model WM WMB & Maybe Others, It Looks to be in good Condition ..... Good Replacement If yours Is Stuck, Missing, Has stripped Threads, Or some other type of damage !!!

Original mccormick deering ihc m hit miss 1 1/2 hp gas engine carburetor comp

Baldwin, Wisconsin, United States
Jan 31st

This is an Original Gasoline Carburetor, Complete with the Bolts , Plug wire holder & Hardware For The "IHC" International Harvester Co. Or McCormick Deering Gas Engines...... This Came off A 1 1/2 Hp "M" Gas Engine, That I parted Out.

Nice original mccormick deering ihc m hit miss 1 1/2 hp gas engine crank shaft !

Baldwin, Wisconsin, United States
Jan 31st

This is an Original Crank Shaft For The "IHC" International Harvester Co. Or McCormick Deering Gas Engines...... This Came from A 1 1/2 Hp "M" Gas Engine, That I parted Out.

Nice original mccormick deering ihc m hit miss 1 1/2 hp gas engine rod & piston

Baldwin, Wisconsin, United States
Jan 31st

This is an Original Rod & Piston For The "IHC" International Harvester Co. Or McCormick Deering Gas Engines...... This Came from A 1 1/2 Hp "M" "Spark Plug style" Gas Engine, That I parted Out.

Rare maytag racer drive wheel pulley hit miss gas engine model 82 72 92 upright

Baldwin, Wisconsin, United States
Jan 31st

These Are New Castings Of The Maytag Racer Drive Wheel & Drive Pulley........ They are in Good Condition, I have Had these for A number Of years "just In Case I Needed them" But Have not..... so I thought I would Offer them For Sale !!!

Waterloo boy & contract hit miss gas engine 1 1/2 - 12 hp 3 igniters & parts !!!

Baldwin, Wisconsin, United States
Jan 31st

This is a Parts Lot, with 3 Igniter Bodies & 2 Movable Shafts And Some Misc. Pieces for the Waterloo Gas Engines, Including Most All Of The Waterloo Contract Hit & Miss Governed Gas Engines, These Will Fit All The Engines From 1 1/2 HP To the 12 Hp Engines, That Uses A standard Under Strike Type Igniter. These are About 3" in Dia.

Associated hit miss gas engine 1 1/2 - 12 hp 3 igniter & part abs casting

Baldwin, Wisconsin, United States
Jan 31st

This is an Igniter Body & A trip Piece for the Associated Hit & Miss Governed Gas Engines, These Will Fit All The Engines From 1 1/2 HP To the 12 Hp Engines, That Uses A standard Under Strike Type Igniter. This is An Original Igniter Body With the "ABS" Casting Letters, & The Finger Trip Piece....... There Are not Enough Parts to Make A complete Igniter, But They Are Available & With A little Work I know it Could be Made to work !!!

Nice old fairbanks morse headless 1 1/2 hp hit miss gas engine crank handle

Baldwin, Wisconsin, United States
Jan 31st

This is an Original Starting Crank Handle, For The 1 1/2 - 2 Hp Fairbanks Morse Hit & Miss, Or Throttle Governed Gas Engines. I think This Would Be correct for The Headless & All the Earlier Z Engines...... Looks like it Has Part # ZA 728B Opening Is 1 7/16" For A 1 3/8" Crank Shaft.