Fittings & Plates (Workholding Tools) for sale, page 48

2 a2-6 lathe driver face fixture back plate 9.45" dia. d5689

Long Beach, California, United States
Jun 3rd

Sottof Sales You are purchasing the actual item in photos, may have rust and marks from use. This is a lot of two plates with various holes in them. The largest part of the mounting taper is approx.

2 a2-6 lathe driver face fixture back plate 9.45" dia. d5690

Long Beach, California, United States
Jun 3rd

Sottof Sales You are purchasing the actual item in photos, may have rust and marks from use. This is a lot of two plates with various holes in them. The largest part of the mounting taper is approx.

Knee, machinist knee 4" x 3" x 2-15/32" h.d. right angle cast iron knee

Saunderstown, Rhode Island, United States
Jun 3rd

For your Consideration is this Machinist / Toolmaker Knee ... Heavy Duty Right Angle Cast Iron Knee ... Knee measuremen

Hardinge hv-4 5c 24-stop collet rotary fixture

Lorain, Ohio, United States
Jun 3rd

Up for sale is a Hardinge HV-4 5C 24-Stop Collet Rotary Fixture. Used in good condition. Any photographs with rulers are to give an estimate of scale and aren't intended to portray precise measurements of parts.

12 7/8" cast iron face plate casting for lathe diy project

Maiden, North Carolina, United States
Jun 3rd

Here is a handy-dandy casting seasoned over 45 years. There are no apparent worm holes in the casting. The dimensions are noted with pictures, and yes it weighs in at 42 pounds, and since it is so bulky I cannot ship it.

Lot of carr lane, vulcan, teco mill work hold down clamps forged, tapped heel

Saint Paul, Minnesota, United States
Jun 3rd

LOT OF CARR LANE, VULCAN, TECO Mill work hold down clamps forged, tapped heel Including the following: Carr Lane CL 65 CS CL 10 CS TECO 30914 Vulcan # 54 Vulcan # 66 T nuts and Bolts

Lot of carr lane, vulcan, bridgeport mill work hold down clamps forged, tapped

Saint Paul, Minnesota, United States
Jun 3rd

Lot of Carr Lane, Vulcan, Bridgeport Mill work hold down clamps forged, tapped heel Including the following: Carr Lane CL 85 CS CL 86 CS CL 18 CS CL 80 CS CL 6 FRCS Bridgeport Vulcan # 58 Vulcan # 66 T nuts and Bolts L13

Lot of carr lane and vulcan mill work hold down clamps forged, tapped heel

Saint Paul, Minnesota, United States
Jun 3rd

LOT OF CARR LANE and VULCAN Mill work hold down clamps forged, tapped heel Including the following: Carr Lane CL 6 FRCS CL 80 CS CL 77 CS CL 78 CS CL 85 CS Vulcan # 58 T nuts and Bolts L12

Lot of carr lane, vulcan, j & s tool mill work hold down clamps forged, tapped h

Saint Paul, Minnesota, United States
Jun 3rd

Lot of Carr Lane, Vulcan, J & S Tool Mill work hold down clamps forged, tapped Heel Carr Lane CL 86 CS Vulcan #78 Vulcan #58 Vulcan #59 J & S Tool Company Model 105 Double action jaw clamp

Face/drive plate 4-1/8" round with 1/2 by 20 threads per inch pn 218

Williamston, Michigan, United States
Jun 3rd

I am parting out a Craftsman 109.20630 metal lathe I recently purchased and this 4-1/8 inch round face plate was with the lathe. It was very rusty so I have cleaned and wire brushed it and tapped the spindle threads to clean them up. There is some pitting on the face in several spots and part of the mounting threads are corroded.

Face/drive plate 4-1/8" round with 1/2 by 20 threads per inch pn b3518&dog

Williamston, Michigan, United States
Jun 3rd

I am parting out a Craftsman 109.20630 metal lathe I recently purchased and this 4-1/8 inch round face plate and dog was with the lathe. It was very rusty so I have cleaned and wire brushed it and assembled it to the spindle and it fits. There is some pitting on the face in several spots.

Craftsman 109 change gear,bolts,washers,sleeves,bushings & extras

Williamston, Michigan, United States
Jun 3rd

I am parting out a Craftsman 109.20630 metal lathe I recently purchased and these change gear assemblies and extra parts were with it. You get two complete change gear sleeve & bushing assemblies with hardware. You also get 2 extra bushings and some odds and ends as shown.

36" long x 5 1/4" wide t-slot milling table slide fixture plate work hold down

Findlay, Ohio, United States
Jun 3rd

This listing is for a t slot plate 36" Long 5 1/4" Wide Surface 1/2" T slot (top width) Casted Plate This plate was removed from a tool grinder. It is in good used condition. Please review pictures for more detail.

Hardinge c26 7" t slot face plate

Montebello, California, United States
Jun 3rd

Hardinge C26 7" t slot face plate Item is in Good shape Nice one (#106)

Suburban magnetic chuck 6"x6" sine plate

Crestline, California, United States
Jun 3rd

Up for Auction Suburban Magnetic Chuck 6"x6" Sine Plate Lightly used. Missing identity plate. I looked for the manufacturer plate in my Kennedy but could not find.

Hardinge hlv speed indicator plate/dial

Haverhill, Massachusetts, United States
Jun 3rd

Machine set up tooling fixture spring-return dovetail slide block

Lorain, Ohio, United States
Jun 3rd

Up for sale is a Machine Set Up Tooling Fixture Spring-Return Dovetail Slide Block. Measures approximately 4" wide x 10" long x 2-3/4" high. It has approximately 1-1/4" of slide movement.

Heinrich tool co. # 1ac 8" collet pneumatic fixture with foot pedal control

Coventry, Rhode Island, United States
Jun 3rd

For 5C Collets

5-1/2" x 8" x 10" steel machine right angle iron

Hurdle Mills, North Carolina, United States
Jun 2nd

Machined Right Angle Iron 5-1/2” Width 8” Depth 10” Height

Heinrich vise 3" #sa-33 single-acting air vise

Louisville, Kentucky, United States
Jun 2nd

THIS AUCTION IS FOR A USED HEINRICH TOOLS 3" #SA-33 SINGLE-ACTING AIR VISE $$$$ PLEASE EMAIL OR CALL 1-812-968-5230 IF YOU HAVE ANY QUESTIONS.$$$$ PLEASE CHECK OUT MY AUCTIONS. HEINRICH Single-Acting Air Vise - Model - SA-33 Jaw Width - 3" Jaw Opening - 3-1/8" Model # SA-33 Jaw Width 3" Jaw Opening 3-1/8" Jaw Depth To Bars 1-1/4" Features Diaphragm type, spring return air cylinder, 3/8" maximum. Holding power, 15X air pressure.