flat bearing for sale, brand-new and used.

Ball-Bearing Rotainer for 1 3/4” dia. Post (5.25” long)(g) > Satisfaction guaranteed or your money back This auction is for: ONE Ball-Bearing Rotainer for 1 3/4” Post (5.25” long) OD = 2 inches DANLY Designed to rotate on the post, as well as maintain its vertical motion, The ROTAINER® was developed to greatly reduce the amount of tracking. The disengagement of the guide post from the bushing by 1/4" at the top of the stroke will allow the ROTAINER® to rotate 360° on the guide post.

Ball-Bearing Rotainer for 2” dia. Post (5.25” long)(f) > Satisfaction guaranteed or your money back This auction is for: ONE Ball-Bearing Rotainer for 2” Post (5.25” long) OD = 2.5 inches DANLY 6-1621-822 Designed to rotate on the post, as well as maintain its vertical motion, The ROTAINER® was developed to greatly reduce the amount of tracking. The disengagement of the guide post from the bushing by 1/4" at the top of the stroke will allow the ROTAINER® to rotate 360° on the guide post.

Ball-Bearing Rotainer for 2” dia. Post (5.5” long) (e) > Satisfaction guaranteed or your money back This auction is for: ONE Ball-Bearing Rotainer for 2” Post (5.5” long) OD = 2.5 inches DANLY Designed to rotate on the post, as well as maintain its vertical motion, The ROTAINER® was developed to greatly reduce the amount of tracking. The disengagement of the guide post from the bushing by 1/4" at the top of the stroke will allow the ROTAINER® to rotate 360° on the guide post.

Ball-Bearing Rotainer for 2” dia. Post (5.5” long) (d) > Satisfaction guaranteed or your money back This auction is for: ONE Ball-Bearing Rotainer for 2” Post (5.5” long) OD = 2.5 inches READY 1429294/6-1623-822 Designed to rotate on the post, as well as maintain its vertical motion, The ROTAINER® was developed to greatly reduce the amount of tracking. The disengagement of the guide post from the bushing by 1/4" at the top of the stroke will allow the ROTAINER® to rotate 360° on the guide post.

Ball-Bearing Rotainer for 2” dia. Post (7.5” long) (c) > Satisfaction guaranteed or your money back This auction is for: ONE Ball-Bearing Rotainer for 2” Post (7.5” long) OD = 2.5 inches DANLY Designed to rotate on the post, as well as maintain its vertical motion, The ROTAINER® was developed to greatly reduce the amount of tracking. The disengagement of the guide post from the bushing by 1/4" at the top of the stroke will allow the ROTAINER® to rotate 360° on the guide post.

Ball-Bearing Rotainer for 2.5” dia. Post (8.75” l)(a) > Satisfaction guaranteed or your money back This auction is for: ONE Ball-Bearing Rotainer for 2.5” Post (8.75” long) OD = 3 inches Designed to rotate on the post, as well as maintain its vertical motion, The ROTAINER® was developed to greatly reduce the amount of tracking. The disengagement of the guide post from the bushing by 1/4" at the top of the stroke will allow the ROTAINER® to rotate 360° on the guide post.

(Blue) Makerbot Replicator 1 & 2 Extruder Upgrade, Thingomatic w/MK7 Extruder - Delrin Plunger Replacement: I had real problems using the delrin plunger system so I purchased a spring loaded extruder upgrade but still had a few problems with not having enough pressure from the spring to keep the plastic against the drive gear (slippage). I redesigned a similar upgrade and use a heavier and stiffer spring then what I originally was using.

Our Bowder extruder demo video: Motor Specification: Holding Torque: 5.5Kg.cm Rated Voltage: 4.2V NO.of Phase: 2 Step Angle: 1.8° ± 5% Resistance Per Phase: 2.8?± 10% Inductance Per Phase: 4.8mH± 20% Current Per Phase: 1.5A Shaft: 5mm diameter w/ one flat

This is an upgrade kit for the Makerbot Replicator 2x Delrin Plunger Extruder. It is the kit only. The extruder upgrade can be printed from: http://www.thingiverse.com/thing:42250 (2x) Spring Dimens

(Red) Makerbot Replicator 1 & 2 Extruder Upgrade, Thingomatic w/MK7 Extruder - Delrin Plunger Replacement: I had real problems using the delrin plunger system so I purchased a spring loaded extruder upgrade but still had a few problems with not having enough pressure from the spring to keep the plastic against the drive gear (slippage). I redesigned a similar upgrade and use a heavier and stiffer spring then what I originally was using.

This S/S 325 gallon tank is completed with a stainless heat coil in the bottom, an agitator, and probes. The tank is 42" in diameter by 48" high (straight side). It includes a 6" cone at the bottom.

This is a NO RESERVE auction for ONE Lightning International PTY., LTD Powerglide Type 8 electric straight-knife cutting machine. Overall in good condition, works great, needs a new blade. Self-sharpening.

WOLF FABRIC/CLOTH CUTTER - MACHINE PARTS 3552001 4" GEAR W/ BEARING 3604083

WOLF CLOTH / FABRIC CUTTER MACHINE PARTS - 3560000 KNIFE BEARING SHIM .001 LOT OF 7 .366 inch id .533 od (these measurements are approx )

I am selling the individual cap drive ( sash base frames ) from a Tajima TMEHC 12 head ( Fits all Tajima cap machines that use this kind of cap frames ) which was never used and recently mounted on the machine just to be cleaned and lubricated. I will guarantee that the frames are in perfect condition with no scraped bearing path, movements, or bad bearings or parts. You will receive the complete individual drive with all parts, shafts, screws, bearings, roller, bushings, etc;.