flat head stainless steel screws for sale, brand-new and used.

Brand new bucket of Stainless Steel T-15 head size screws. There are 1750 count in this bucket and they are made as advertised for hardwood decking. #7 by 1 5/8" long with a brownish painted head (as seen in the pics).

TEN, Unopened 1 pound boxes of 3 Inch stainless steel square drive exterior screws. Great for decks or fencing. Coarse thread type 17 point.

Approx. 500 5/16-18 x 2 1/2 flat head stainless steel screws.

This auction is for a nice Lot of 100 Flat Head Socket Phillips Head Cap Screw (Bolt) 5/16-18 3/4 inch Stainless Steel Restaurant Grade See Pictures for better details I give the best description and condition as I can, but if I do make an error, I do apologize and will fix the error ASAP. Thank you for looking.

This auction is for a nice Lot of 100 Flat Head Socket Pin Head Cap Screw (Bolt) 5/16-18 1/2 inch Stainless Steel Restaurant Grad See Pictures for better details I give the best description and condition as I can, but if I do make an error, I do apologize and will fix the error ASAP. Thank you for looking.

Goulds Bruiser Pump 1/2 HP 10 GPM  Submersible water well pump that features abrasive handling construction, stainless steel casing, and a check valve that can be easily removed for drain-back systems or replacement. Manufacturer: Goulds Model: 10SB05-412 Horsepower: 1/2 GPM: 10 Voltage: 230V, 60HZ Phase: Single-Phase, 3-wire Features: Abrasive Handling Construction: Impellers designed with flat wearing surface which provides effective sand handling capabilities.

THIS IS A LARGE CABINET LOADED WITH STAINLESS STEEL HARDWARE. THERE IS A LOT OF DIFFERENT SIZES. WASHERS --NUTS--BOLTS--SCREWS STANDARD.

Box of #10-3 inch stainless steel 302 T25 tamer proof security screws. Sheet metal style, but coarse enough for wood. 500 pieces, weighs about 9 pounds.

Wire EDM Vise And Mount Block Vise All parts are made with 420 stainless steel and hardened to 45-55 RC Vise is precision ground +/-.0002" flat/parallel. Vise will open up to almost 3.5 inches Each vise comes with a removable setup rail!!! Mount Block Made with 420 stainless steel and hardened to 45-55 RC precision ground +/- .0002 flat/parallel comes with stainless socket head cap screws for bolting together Thanks Brad B.

Wire EDM V-Block And Mount Block All parts are made with 420 stainless steel and hardened to 45-55 RC V-block is precision ground +/-.0002" flat/parallel. Each V-block comes with a removable setup rail!!! V-block will hold up to 2.5 inch diameter or a 2.75 inch square piece.

Multi Position V-Block Will hold up to a two inch diameter Bottom Plate is .5 X 5 X 5 (inch) All Parts are 420 stainless steel and hardened to 48-52 RC Main V-Block can be set in three different positions. There is a straight rail that bolts to all four sides of the bottom plate for ease of removing the V-Block and setting back up. There is a low profile V-Block that can also be set in two different positions.All socket head cap screws (stainless) in picture are provided.

Wire EDM V-Block 1.5 X 5 X 5 (inch) Will hold up to a 3 inch diameter. 420 stainless steel (hardened 48-52RC) With - clamp - set up rail - stainless socket head cap screws - side rail (for standing block up or on its side) - (3) clamp screws The slotted screws are for M8 and M6 socket head caps screws they are machined 50 mm apart so these will work in any Wire EDM machine. Main Block is precision ground +/- .0002" flat/parallel

var itemNumber = window.ebayItemID ?

var itemNumber = window.ebayItemID ?

Modular VESA Mount Keyboard Tray -V2 by SDS This sale is for the Keyboard Tray only! Any thing else in the photos is for demonstration only. This is the latest Model, with two small bends reinforcing the tray to remove bounce.

Brand-new never installed come as shown you will receive unit that is shown Its very large and weighs 37 lbs built like a tank shipping is as cheap as I can go Reflector Housing: One-piece die-cast, low copper (<0.6% Cu) aluminum alloy with integral cooling fins. Rotates against ballast housing to provide 10° of adjustment with degree markers cast into the housing. At 0° adjustment, lens is totally concealed from view above horizontal with fixture aimed downward.

MODIFIED UNISAW TABLE WING - ADDS ROUTER TABLE CAPABILITY TO YOUR EXISTING TABLE SAW. The heavy cast iron extension wing, when combined with the mass of your vintage Unisaw, makes a great router table. This sale is for one (1) Unisaw extension wing, modified as described below, to accept a Bosch router, adding a very stable and functional router table on the far right side of your Delta table saw.