jaws 8 for sale, brand-new and used.

Machinist Vise as Shown Maker unknown Cleaned up some and tested ok. ( Was in storage ) 1 1/2" x 4" wide jaws The Jaws are 1 3/4" from the top to the bed of the vise with reliefs in the bottom of the bed to keep work flat Jaws open up to 3 7/8 ( can get another 1/16 more max ) You can replace the jaws by removing the screws that hold them in and install your own if you like. Vice is in Good Condition.

H & R Soft Lathe Chuck Jaws Jaw Type

(2) PAIR (sets) of Machinist Vise JAWS. These can also be used as Parallels or Blocks. Both sets are hardened and Ground.

Accessory jaws for PSI "C" series Chucks. For use on lathes with 12" swing or higher.  This auction is for just the jaws. I do not have the 8 rubber grips, and I only have one screw.

VINTAGE CAST IRON WILTON DRILL PRESS VISE MACHINIST HAND TOOL. MADE IN U.S.A.. IT IS 3 1/8" TALL AND 9" LONG OVERALL.

VINTAGE CAST IRON SWIVEL BENCH VISE HAND TOOL. THERE IS NO MAKERS MARK. IT IS 6" TALL AND 8 1/2" LONG.

Phil / 12.8.14 / P 12 E / 54390 TF 9.15.15 Interstate Model 08600306 Lathe Chuck Type - SET-TRU Adjustable Jaw Type - Self Centering Number of Jaws - 3 Diameter - 8” Through-Hole Diameter - 2.2640” Shipping Weight: 45 Lbs. Shipping Dimensions: 13” x 13” x 9”

Gibraltar Lathe Chuck Chuck Type - Self-Centering Chuck Diameter - 8” Number of Jaws - 3 Adjustable - Yes Mount - Plain Back Through-Hole Diameter - 2.2640” Body Material - Steel Number of Jaw Pieces - Two-Piece

Bison Lathe Chuck Type - Self Centering Number of Jaws - 3 Jaw Type - Two-Piece Diameter - 8” Through-Hole Diameter - 2.1654" Mount - Front Mount Material - Forged Steel

Wilton 6" Hitch Mounted All-Terrain Vise

Product Name 10 Ton Straight Bar Puller Set Features and Benefits: Larger 10 ton puller set Versatile and strong Includes 4 sets of jaws for different applications Comes in a plastic carrying case Kit includes: (1) 10" spread; (3) spring clips; (2) cap screw jaws, 2-15/16" reach; (2) double reach wide jaws; (2) narrow jaws with 8" reach; (1) 12" forcing screw; (1) 7" short forcing screw.

H & R 1.5 mm x 60? 1018 Steel Lathe Chuck Jaws Jaw TypeSquare

Athol 614 Vise Fixed Base 4 Inch Jaws Heavy Vintage Vice Up for sale is my Athol 614 vise. I got this vise at a farm auction a few years ago, and have used it as my main vise. I recently replaced it with a Wilton bullet, so I am passing it on.

Iron Parrot Vise 360 Degree Swivel Mechanism Lay Vise Flat Jaw Holes Woodwoker Iron Parrot Vise Product Description: This unique Iron Parrot Vise swivels a full 360-degrees and then locks in place when the jaw is tightened. This handy Iron Parrot Vise can be used in nearly any position for a range of applications. Capable of clamping in the upright position, side-to-side or at any angle.

Product Name 5-1/2" Tradesman Vise Features and Benefits: Wider Jaws provide greater clamping surface Fully enclosed spindle and nut increases the life of the vise Large anvil work surface Precision turned sidebar 360° swivel base with double lockdowns Proudly made in the USA, the Tradesman round channel vise is designed to handle the most demanding clamping applications. Unlike most vises that have a fixed center nut, the Tradesman round channel vise nut is anchored at the rear.