lock nut washer for sale, brand-new and used.

Up for sale here is this vintage Buss fuse holder. It is used but in great working condition and would look great on a tube amp or guitar amp or whatever you put it on. It holds a regular-size fuse and has the lock washer and nut as well.

7r custom teeth lock washer stop crimpers , old vintage nos

Stainless 4" tank to hose coupling - quick connect for hose - twist lock plug marked with A5763/8401 ON FLANGE marked with A5665/8528 ON QUICK CONNECTOR @ 15 DEGREE TURN FOR QUICK CONNECT COMES WITH LOCKING FLANGE NUT, FLANGE WASHER AND O-RING

THIS ITEM IS FOR 1 (ONE): ITW MINIATURE ROTARY SWITCH SINGLE POLE -- 8 POSITIONS NON-SHORTING (break before make). This switch has ONE installed stop for 8 positions (non-moveable) The switch has gold plated PC type terminals, but are easily soldered to for wires. DIM: 1/2" OD X 1/2"L including PC terminals.

You Are Purchasing a LOT of Fairmont Parts that Includes: Part# Description Qty

THIS ITEM IS FOR 1 (ONE): GRAYHILL MINIATURE ROTARY SWITCH: 1 POLE -- 6 POSITIONS FIXED STOPS ** NON SHORTING (break-before-make) ** 30 degree index RATING: .25A - 115vAC DIM: 1/2" OD X 1" behind panel. SHAFT: 1/8" X 3/8"L W/FLAT GRAYHILL P/N: 09A30-01-1-6N

Lot of 10, Motorola SZM10002-37 mounting kit for stud mount rectifiers, triacs, etc. These are made for stud mount devices and have the usual hardware included: washer (inner diameter 7.3mm), nut (inner diameter 5.5mm), lock washer, mica insulators, solder lug (inner diameter 7.6mm) and insulating ring (inner diameter 7mm). Alltronics part#28Z023.

Autoparts Wholesalers - Official eBay Store

Don-Jo Latch Protector GLP-307-630 Stainless Steel LHR 2-5/8" x 7" Don-Jo GLP-307-630-LHR For Aluminum Entrance Doors-solves pull handle interference - 2-5/8" x 7" Fastening Type: 1 ea. 5/16-18 x 2-1/4" Carriage bolt w/Acorn nut & washer, 1 ea. Drive in Rivet Features: Fits over cylinder - lock removal NOT required Hand carriage bolt and rivet supplied No specific tools required 3/8" offset Center of cylinder hole is 2-1/2" from end of plate Dimensions: 2-5/8" x 7" Gauge: 12 ga.

About us Shipping Payment

WELCOME TO RIVERCITY INDUSTRIAL SUPPLY! PHONE: 763 789 BOLT (2658) FAX: 763 789 NUTS (6887) 1 BAG OF 200 PIECES #8 AN960 Flat Washer Cadmium yellow finish -8 Made in USA Military spec. AN Washer Specs:

Steel Hex Nut, #10-32 Threads (Pack of 100)

The Hillman Group 829724 3/8 by 16-Inch Stainless Steel Nylon Insert Locknut, 50-Pack

payment | shipping rates | returns Burndy HFB42P1 Bar Clamp Assembly Component, 4" Copper Bus Bar Clamp Run, 2" Copper Bus Bar Clamp Tap, 4 Bolt, 4 Nut, 4 Split Lock Washer, 3/8" Bolt Diameter, 5.75" Length, 5.75" Width, 240lb Recommended Tightening Torque Product Catego

3/8-16 X 6-1/2" stud kit (10pcs) with nuts and washer Hot Dipped Galvanized 10pcs 3/8-16 X 6-1/2" studs hot dipped Galvanized 30pcs 3/8-16 hex nut Hot dipped Galvanized 20pcs 3/8" flat washer hot dipped Galvanized 20pcs 3/8" split lock washer hot dipped Galvanized

These are 1/2" X 3 1/2" stainless steel bolts. These are new never used old stock. There is a stainless nut and a stainless lock washer on each bolt.

Solar Controller solar blocking diodes Diversion load regulator Charge regulator Charge controller Battery regulator 12 volt 24 volt 48 VDC volt wind power charge controller dump load dive This auction is for Ten (10) of the #75RIA160 75 Amp diodes. Comes professionally packed in white box and protected by

This precision potentiometer is new in original bag. Diameter is 3 1/4" Height almost 3" plus shaft 7/8" long, 1/4" diameter. Because it is so large it is a high resolution pot.