Loctite Hysol E-05mr Moisture Resistant Fast Setting Crystal Clear Epoxy

US $18.99

North Richland Hills, Texas, United States
Jan 30th

Open on mobile:
QR code

LOCTITE Hysol E-05MR is a general purpose two-component epoxy adhesive which develops high strength on a wide range of substrates. The gap filling properties make this adhesive system suitable for rough and poorly fitting surfaces made from metal, ceramic, rigid plastics or wood. Once mixed, the two component epoxy cures at room temperature to form an ultra clear adhesive bondline with excellent impact and temperature resistance. TYPICAL APPLICATIONS Ideal for bonding plastic, metal, glass, wood, ceramic, rubber, and masonry materials where flexibility is needed. Designed for a variety of applications such as flex circuits, cable boots, and staking fillet bonds. Well suited for applications that require an ultra-clear bondline. Technology Epoxy Chemical Type Epoxy Appearance (Resin) Ultra clear Appearance (Hardener) Ultra clear Appearance (Mixed) Water wMe clear liquid " Components Two componenl - requires mixing Viscosy Medium Mix Ratio, by volume - Resin : Hardener 1 :1 MixRatio,by weight -Resin : Hardener 1 :1 Cure Roomtemperature cure afler mixing Application Bonding Chemical/Solvent Resistance Aged under conditions indicated and tested @ 22 °C. % of initial strength Environment oc 500 h 1000 h Air 87 135 162 Motor oil (10W30) 87 124 133 Unleaded gasoline 87 12 21 Water/glycol 50/50 87 26 20 Water 22 140 126 Acetone 22 99 101 lsopropanol 22 99 88 Salt fog 22 98 90 Condensing Humidity 49 78 46 95% RH 40 110 108 Handling Mixing: This product requires mixing two components together just prior to application. Complete mixing is necessary. The temperature of the separate components prior to mixing is not critical, but they should be close to room temperature. Application Mixing - Cartridges: Place cartridge in proper dispenser. To begin using a new cartridge, remove the cap and dispense a small amount of adhesive, making sure both parts A & B are extruding. Attach nozzle and dispense approximately 1-2" before applying onto the part to be bonded. Partially used cartridges should be stored with the mixing nozzle attached. To reuse, remove and discard the old nozzle, attach the new nozzle, and begin dispensing. Mixing - Bulk: Combine Part A (resin) and Part B (hardener) in the correct ratio and mix thoroughly until the color and consistency are uniform. EPOXI-PATCH® Tube Kits have been designed so that squeezing EQUAL LENGTH BEADS of Part A & Part B will give proper ratio. Ratios given above can be used for measuring larger amounts. Mixing the adhesive just prior to use is recommended. Heat buildup during or after mixing is normal. Do not mix quantities greater than one pound as dangerous heat buildup can occur causing uncontrolled decomposition of the mixed adhesive. Mixing smaller quantities will minimize the heat buildup. Application Bonding surfaces should be clean and dry. Once the adhesive is applied, the bonded parts should be held in contact until the part has developed handling strength. It is not necessary to clamp the parts unless movement during cure is likely. Cure Complete cure is obtained after 24 hours at room temperature. HYSOL 608 will achieve handling strength in 10- 5 minutes at 77°F (note: this can vary with different bond configurations). Hysol 608 can also be fully cured with heat such as; 5-20 minutes at a maximum of 150°F temperature. Clean Up It is important to remove excess adhesive from the work area and application equipment before it hardens. Many common solvents and citrus cleaners are suitable for removing uncured adhesive. Consult with your supplier's information pertaining to the safe and proper use of solvents. Packaging 4 gram Foil Packs 2.8 oz. Epoxi Patch Tube Kits 50 ml and 200 ml EPS Cartridges Quart, One Gallon, and Five Gallon Systems