Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 0

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 1

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 2

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 3

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 4

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 5

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 6

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 7

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 8

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm x 37mm x 20mm Laser Diode, US $9.99 – Picture 9

Lot 4 Tiger Milled Aluminum Heatsinks, Heat Sinks 37mm X 37mm X 20mm Laser Diode

US $9.99

Springfield, Tennessee, United States
Jan 29th

Open on mobile:
QR code

2453XB3D.21 New TTI (Tiger Technologies Inc.) RoHS Compliant Aluminum Heatsinks, or Heat Sinks, With Heat Conductive Tape and Nylon Board Mounting Pins; Part Number A80-0000308-00L, or 210-E185761. Each bid quantity is for a Lot of Four (4) Heatsinks. You may bid / buy any number of lots, up to the total quantity available above. These were purchased at an electronics supplier liquidation earlier this year, and they were brand new in the original factory boxes. We packaged them in heavy Ziplok bags so they will ship fast and cheap. These are either entirely milled, or they were extruded and then extensively milled after extrusion. Whichever way they were made, the resulting product is very precise and very flat. Considering the fin spacing and pattern, they could be used for either forced air (fan cooled) or ambient air (without a fan) applications. Comes with a pair of spring loaded nylon posts that hold the heatsink securely against the device being cooled. Or, if the nylon posts and aluminum ear tabs are not needed, they could be easily snipped off with a pair of side cutting pliers. The thermal conductive tape patch on the mounting surface is printed with "Parker Sentra Team." Best we can tell, it comes from Parker Hannifin's Chomerics Division. Buy now, and get quality name brand heatsinks for less than the cost of cheap imported stuff. Note: The bags appear to show only two pieces per bag, however, the heatsinks are nested to protect the fins during shipment. There are four (4) pieces per bag. According to the calipers Overall length (including mounting post ears): 1.986" / 50.44mm Length (excluding mounting post ears): 1.475" / 37.47mm Overall width: 1.477" / 37.51mm Height: .795" / 20.19mm Minimum web / base thickness: .108" / 2.73mm Mounting post diameter: .098" / 2.49mm Mounting post barb width: .153" / 3.90mm Mounting post spacing (measured parallel): 1.705" / 43.30mm x 1.198" / 30.44mm Mounting post spacing (measured diagonally): 2.099" / 53.31mm Mounting post length (spring fully compressed): .203" / 5.15mm Adhesive pad dimensions: .675" / 17.13mm (square)

Condition:	New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. ...	Brand	Tiger Technology Inc.
Other Name	Heat Sinks
Model	210-E185761
RoHS Compliant	Yes
MPN	A80-0000308-00L
Special Feature #1	Heat Conductive Tape
Type	Heatsinks
Special Feature #2	Nylon Board Mounting Pins
Material	Milled Aluminum
Quantity	4
Dimensions	37mm x 37mm x 20mm
SELLER LOCATION	USA
Other Part Number	210-E185761