mixer gas for sale, brand-new and used.

Wire Whip Attachment Condition:

This is an extremely hard to find original fuel mixer for a Galloway Handy Andy hit and miss gas engine. It is in excellent used condition with no cracks, breaks, or repairs of any kind. The original fuel needle moves as it should.

This is a rather hard to find original fuel mixer or carburetor for a Fairbanks Morse Z gas engine. It is in good original condition with no cracks, breaks, or repairs of any kind except that it needs a new fuel jet that delivers gas to the head. This is nothing more than a small piece of copper tube in place where my finger is pointing in one of the pictures.

Here is a great piece that fits an early Stover hit and miss engine! This mixer is NOS - came from a hardware store about 40 years ago and has been sitting on our shelf since then. It looks really good and shows no damage or problems!

This is a very hard to find original fuel mixer or carburetor for a Root and Vandervoort gas engine. It is in excellent used condition as can be seen. There are no cracks, breaks, or repairs of any kind.

This is a very hard to find original fuel mixer or carburetor for a 1 1/2hp or 2hp Dishpan Z Fairbanks Morse gas engine. It is in excellent used condition as can be seen and still has most of its original red paint on it. It is part number ZAN4A.

STOCK POT RANGE, GAS Imperial, Model No. ISPA-18 Stock Pot Range, gas, (1) three ring burner, manual controls, open front cabinet base, cast-iron top grate, stainless steel front and sides, 6” adjustable legs with adjustable feet, 90,000 BTU

YOU ARE BUYING ONE: NEW Victor Medium Duty Torch Head 0381-0418, CA1350 100 Series. ALSO COMES WITH 3 NEW TIPS, 1- GPN TIP,

New Eclipse Vari-Set Mixer Cat#648VS Low Pressure Proportion Mixer 2" NPT Mixture Outlet, 1 1/2" NPT air Inlet, 1 1/2" NPT Gas Inlet

University surplus Spex 5100 mixer mill. Retail is over $2500 but you can buy ours for a lot less. Unit looks good,powers on, and timer works -could find no issues with it.

Here we have a 3/4" brass fuel mixer for an old hit & miss or marine gas engine. It`s made by the General Valve Co. of New York.

This is an extremely hard to find original fuel mixer or carburetor for a Nelson Brothers throttling governor or kerosene engine. It is in excellent original used condition with no cracks, breaks, or repairs of any kind except that one of the screws that hold the air damper horn on has been turned off in a hole. This should be a pretty easy fix with just a little patience.

This is an extremely hard to find original fuel mixer or carburetor for a Sandwich Pine Tree milker engine. It is in excellent original used condition with no cracks, breaks, or repairs of any kind except for the cast iron tab on the end of that holds the throttle rod. It has an old farmer fix that has worked more than once!

New cast iron reproduction mixer assembly for the 3hp hit and miss, battery equipt, red line Z model. If you have needed one you know how hard it is to find an original, now you can complete your project without the search. Complete with fuel jet, line and check valve.

Here is an original carburetor or fuel mixer for a Galloway engine. It is in great shape but it is missing its needle valve. I am not sure what size of engine this is for, maybe a 4hp to 7hp?

Here is a Lunkenheimer 3/4" LH carb or mixer. There are NO cracks, breaks, or welds. Check out the pictures and see if you need it.

Here is a Lunkenheimer 1/2" LH side intake carb or mixer. This is a rare little carb! Domestic engines often take a 1" size of this but I have never seen one this small before.

Here is an original carb or fuel mixer for a small IHC Mogul engine. It attaches to the head with one bolt. The needle valve looks and works good.

Hamilton Beach 94950 Mix 'n Chill Commerical Mixer Blender