nut spring for sale, brand-new and used.

Walcom SLIM S HVLP (W3307) primer paint spray gun with 750cc aluminum cup SUGGESTED RETAIL: $292.33 YOUR COST: $146.50 you save 50% Transfer efficiency&

Walcom SLIM I HVLP (W3317) paint spray gun with 1000cc bayonet SUGGESTED RETAIL: $308.88 YOUR COST: $154.50 you save 50%

Walcom STM HVLP 1.2mm NEW DEMO Professional spray gun designed for touch-ups This paint gun is a New, Unused Paint Gun, it has the word DEMO imprinted on the side and has not been used. SUGGESTED RETAIL: $242.00 YOUR COST: $121.00 you save 50% Air flow inlet regulator with manometer. Includes two nylon cups 75cc and 250cc.

We here at SprayPartsUSA.com would like to become your primary source for service parts and accessories for your spray painting and pressure washing equipment. But there’s even more as well. We’re here on eBay with special introductory offerings in hopes that we can entice you to visit us on line.

eBay Template v2.5

This is a good used complete governor gear out of a McCormick Deering 1-2.5 hp engine. It is complete with the spring, rod, nut, ready to put in your engine and used it. The little bracket that the link hooks to, in the picture also is included.

Echoes from the Oil Country (American Machinist Memories), Volumes 1 through 5, originally published in American Machinist magazine in 1901-02. Republished by Lindsay Publications, Bradley, IL, 2005. Each book is 5 1/2 x 8 1/2 paperback.

Fairbanks Morse Magneto Wisconsin engine VH4D and others in super condition .... REDUCED FROM $395.00 Magneto is guaranteed operable, has been once serviced by magneto professional and will fire up any 4 cylinder engine for which this FM-XZE4B7 model is designed. This magneto will operate without further attention other than installing four spark plug connectors.

This is a Complete Hand Throttle to Governor linkage set from the outside hand control to the inside gov. control. This includes the large inside flat spring & the bolt,nut & all items as shown.This whole setup is from an old Fairbanks Morse "ZD" Stationary / Farm Engine.This will fit both the 1 1/2 & 2 H.P.

Fairbanks Morse Magneto Wisconsin engine VH4D and others Removed From a Functioning VH4D Wisconsin The two mounting holes measure about 4" center to center with an elongated rotation adjustment on the lower hole. I counted 27 teeth from its timing mark around the circumference of the gear which can be changed out with common size shaft gear of your own. The gear on this magneto alone is worth $90.00 and is good,, it is held in place with a cottered nut.

New, never been used before Dormont Restraining Devices. Each is individually wrapped in original bag and includes the following parts: Restraining Cable with Two Snap Hooks Spring Loaded Hooks (2) Staple Bracket 1" #10 Screws (4) Plastic Anchors (4)

ATI Tools ATI518NE 1/4" Mini Double Wing Nut Plate Drill Jig (Two Lug Type). Used to install 1/4" miniature two lug double-wing style plate nuts (DWS). Double wing miniature.

5 each lot ATI Tools ATI518K 1/4" Single Wing Nut Plate Drill Jigs (One Lug Type). Used to install standard 1/4" one lug single-wing style plate nuts (SWS). High strength spring steel connects the O-1 hardened head to the aluminum knurled handle.

5 Each ATI Tools ATI518K 1/4" Single Wing Nut Plate Drill Jigs (One Lug Type). Used to install standard 1/4" one lug single-wing style plate nuts (SWS). High strength spring steel connects the O-1 hardened head to the aluminum knurled handle.