Other Woodworking Equipment & Tools (Woodworking Equipment & Tools) for sale, page 188

Scmi sigma 65c front load automatic panel saw

Hatillo, Puerto Rico, United States
Jan 30th

Jet woodworking dust collector collecting system pipe reducer 3" to 2" 2 pack

Punta Gorda, Florida, United States
Jan 30th

1 1/4 inch straight shaper cutter

Seeley Lake, Montana, United States
Jan 30th

This straight cutter came with a shaper I purchased and I have no use for it. The cutter is 1 1/4 tall with a 3/4 inch bore. The carbide is 1/8 inch thick and still has the protective coating on it from a fresh sharpening.

Shaper cutter t bushings, 1-1/4" x 1"

Belleville, Wisconsin, United States
Jan 30th

This is a pair of new shaper T-bushings. Bushes your 1-1/4" bore shaper cutter down to 1". These have the short flange and will work on any 1" spindle.

Door edge shaper cutter

Seeley Lake, Montana, United States
Jan 30th

This door edge cutter came with a shaper I purchased and I have no use for it. The cutter is 1 tall with a 3/4 inch bore. The carbide is just under 1/8 inch thick and still has a lot of life left in it.

Woodworker's push block by axminster

Leicestershire, United Kingdom
Jan 30th

If you have any questions or concerns, please contact us by phone or email. We are Barnes and Woodward, located in Syston, Leicester. We prefer that you to pay for the product without postage if you need us to hold it for longer than 7 days.

V paneling shaper cutter set for 3/4 inch thick stock-tongue and groove

Seeley Lake, Montana, United States
Jan 30th

This V paneling/tongue and grove cutter set came with a shaper I purchased and I have no use for them now. I did set up and run this set for a couple of V paneling cabinet doors and they worked great. The cutters are 1 inch tall with a 3/4 inch bore and are meant for 3/4 inch thick stock.

1 lot 4 carbide inserts cutter head 20mm shank with key hole aluminium wirutex

Notre-Dame-de-la-Paix, Quebec, Canada
Jan 30th

this listing is for 1 lot of 4 cuter head ,uses a 20mm shaft, with keyhole, 20x12x1.5 carbide inserts, all 4 are included and are either new or barely used. let us know if you need more then one or all 4 of them! also check out our other listing we have some insert for this head and other heads available in the same size but made of aluminium or different size.

Three wing freeborn pro line raised panel shaper cutter. pc 14-003

Seeley Lake, Montana, United States
Jan 30th

This Freeborn raised panel cutter came with a shaper I purchased and I have no use for it. The cutter is a proline cutter with a 1 1/4 inch bore and 6 inch diameter. The profile is Freeborn's 14-003.

Bosch spiracut 1638

Buckeye, Arizona, United States
Jan 30th

Bosch Spiracut with guide

Three wing freeborn raised panel shaper cutter. mini pro mc 54-002 profile

Seeley Lake, Montana, United States
Jan 30th

This Freeborn raised panel cutter came with a shaper I purchased and I have no use for it. The cutter is a mini pro cutter with a 3/4 inch bore. The profile is Freeborn's 54-002.

5 pc 3/4" x 20-1/2" 120 grit a/o sanding belts work horse woodworking

Punta Gorda, Florida, United States
Jan 30th

Delta 2 h.p. dust collector 50-761 instruction manual only

Bozeman, Montana, United States
Jan 30th

INSTRUCTION MANUAL ONLY

Geetech 8" 4-knife jointer cutterhead

Auburn, Washington, United States
Jan 30th

Geetech 8" 4-Knife Jointer Cutterhead Fits Powermatic 60B & 60C, JET, Sunhill and other 8" Jointers

8"x6"x6" 45 degree wye duct fitting dust collection

Tazewell, Virginia, United States
Jan 30th

Here is a new never been used wye duct fitting. It is 8x6x6 inches. Great for setting up dust collection system in your woodworking shop.

8"x8"x8" 45 degree wye duct fitting dust collection

Tazewell, Virginia, United States
Jan 30th

Here is a used 8x8x8 45 degree wye fitting. This fitting was installed but never used, it was removed before the dust collection system was put in service. It has five holes drilled on the crimped end where it was installed.

8110112 - new magswitch magfence universal base

Levis, Quebec, Canada
Jan 30th

3/8" x 2-1/2" x 3/4" hole convex cutter

Alpharetta, Georgia, United States
Jan 30th

Shaper cutter molder carbide tipped 3/16" convex radius 3/4" bore 2 1/2" Cutter Head Used. Both now resharpened and honed, ready to work. Diameter (D)- 2 1/2" Radius (R)- 3/16" Width (W) - 3/8" Bore 3/4" carbide tipped Used both now resharpened and honed, ready to work.

Planer knife setting gage for 3-3/16" heads, 20 inch planers

Belleville, Wisconsin, United States
Jan 30th

This is knife setting gauge that will work on planers with a 3-3/16" head. This will cover nearly all of the 20" planers avvailable, Jet, Powermatic, etc. Check your handbook for the actual size as it does make a difference.

Shopsmith mark v complete ,bandsaw,table saw and everything else.lot of extras

Milford, Delaware, United States
Jan 30th

What you are buying is everything you see pertaining to the shopsmith. You get all the attachments,blades an all that other stuff. Bandsaw, tablesaw,all the attachments in the pictures.