General Filters Inc.99 59-99 Features: • Iron and galvanized steel construction for maximum integrity and durability; epoxy powder coat finish • Leak-proof construction with machined gasket seat • Low pressure drop, suitable for gravity flow and one or two pipe systems on pressure type burners • Micronic filtration suited to the smallest oil burner nozz
General Filters Inc. 77 59-77 Features: • Iron and galvanized steel construction for maximum integrity and durability; epoxy powder coat finish • Leak-proof construction with machined gasket seat • Low pressure drop, suitable for gravity flow and one or two pipe systems on pressure type burners • Micronic filtration suited to the smallest oil burner no
Up for consideration are SIX float switches made by Safe-T-Switch model SS1 The SS1 detects down stream clogs in condensate drains and interrupts the thermostat circuit to shut off the unit before flooding occurs. The Model SS1 installs inline at any downward slope from vertical to horizontal. It can also be installed
Honeywell V8043F1051 is a 1" sweat connection two-way on-off low voltage motorized zone valve with screw terminal block electrical connections. It consists of an actuator and valve assembly for controlling the flow of hot water. And designed for cycling (not constantly powered on) applications.
700-201 Robertshaw UPC Number 662013631481/2" SNAP ACTING GAS VALVE W/36" CAP. 7000AS The 700-200 Series snap-action and snap-throttle (modulating) hydraulic controls are combination gas valves, thermostatically operated by a remote temperature sensing bulb.Two types of temperature adjustment models are available. One type is a single capillary model with the temperature adjustment knob on the gas valve itself.
Description for Honeywell V8043E1012 Honeywell V8043E1012 is a 3/4" Sweat Connection Motorized two-way on-off low voltage Zone Valve. Honeywell Zone Valves V8043 consists of an actuator and valve assembly for controlling the flow of hot water.
This auction is for new/unused/untested Robertshaw Safety Magnet UniKit. Product DescriptionGas Cooking Control, Electromagnet Replacement Kit, Gas Connection 1/8 In Pipe, 3/16 In Tubing, 1/4 In Tubing, For Use With 1710 Series Body Outlet Only Model-TS InK In Head, Replaces
The Magnehelic is used to measure fan and blower pressures, filter resistance, air velosity, furnace draft, pressure drop accross orifice plates, liquid levels with bubbler systems, and pressures in fluid amplifier or fluidic systems.
(See below for more details) Fisher Labs XLT30D Liquid Leak Detector with Big Foot and Multi-Sensor New - Factory Authorized Distributor - Factory Warranty Big Foot. Multi-Sensor. Probe Cable Assembly.
Hello, I am selling a complete plastic pipe fuser system for 2" pipe. Has a new heater assembly, insulated bag and attachments for 2" 1-1/4" and 1" for the heating stage. Has extra holding dies for 5/8" pipe.
2066A5H.10 New Norgren Pneufit D Male Adapters, ¼ OD Tube x ¼ NPT, Part Number AMC0404, or D24250428. Each bid quantity is for a Lot of Ten (10) Fittings. You may bid / buy any number of lots, up to the total quantity available above.
HERE IS A BRAND NEW HYDRAULIC HOSE THAT I HAD LEFTOVER FROM MY DEALERSHIP AND FORGOT I HAD IN A TOTE . IT IS 1/2" BY 48" WITH 1/2" PIPE THREAD ENDS .THIS HOSE IS NEW BUT LOOKS LIKE IT WAS DOPED UP AT ONE TIME BUT NEVER ANY OIL THROUGH IT . THANKS FOR LOOKING !!!
3/8" SAE100R2 Hydraulic Hose Assembly with 3/8" Male Pipe 6 Foot in Length Not the Length or Correct Fitting You Were Looking for?????? We customize to your specs!!! A - .375B - 2.12C - .99D - 3/4"
Genuine U.S. Military Issue Surplus Fire Fighting Rubber Hose Assembly with Connectors We are not sure who made this hose assembly, we came up with the following.... Bosch Rexroth GMBH Lohmann P/N: 02114 DLA Land and Maritime P/N: CS4210-0021 Jarvis Engineering Co.
100' of PARKER LP Gas Hose UL21, CGA Type I - Series 7232 Series 7232 is a large diameter, flexible liquefied petroleum gas (LPG)/propane transfer hose for large volume bulk loading/unloading and vibration-resistant onboard vehicle connections. The hose meets all Underwriters Laboratories (UL21) and Canadian Gas Association (CGA Type I) requirements. The construction incorporates multiple braids or plies of textile reinforcement for kink resistance and superior coupling retention.
By clicking "Accept All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyze site usage, and assist in our marketing efforts.