shaft bushing for sale, brand-new and used.

Model

Generac B1262 Replacement Pressure Washer Pump NEW 1750 PSI, GENERAC VERTICAL PUMP 7/8" SHAFT WITH SHAFT KEY RUBBER STABILIZER BUSHING AT BOLT POINTS, TO REDUCE VIBRATION. BUILT-I

Technical Specs Item Belt Drive Motor Motor Application HVAC/R Motor Sub Application Belt Dr Fan/Blower Motor Type Split-Phase HP 1/4 Nameplate RPM 1725 Voltage 115 Frame 48 Enclosure

Hi, this is Don. I took these parts from a busted up engine, but these parts all look pretty good. It looked like about a 5hp engine, but I could not identify it.

Contact me first if you have less than 5 bids before bidding. You are bidding here on a nice lot of six (6) brand new, in the box or plastic, Flowserve parts, as follows: 2 each Sleeve Shaft Mechanical Seal Monel F/Goulds MD 00000361120 Part 3R5967HU 00503768 2 each Collar Drive Item #S-58 316SS 00507018 4R4034DB I think these are slurry seals... 2 each Bushing Mechanical Seal Item S-24 Bronze 00512419

FROM BASKET CAST-NO POSITIVE LOCATIONS SEE PHOTOS VIOLET MARKED DUAL GEAR HAS TELESCOPING SHAFT WITH BRONZE BUSHING HAS SOME "PLAY" FEW MARKS ON TEETH (MINOR) GEARS ON ARM ASSEMBLY. "RED" GEAR HAS 2 CHIPPED TEETH GEAR IS 3/8" WIDE CHIPS LESS THAN 1/2 WIDTH. BLUE GEAR LOOKS GOOD.

Pulled from a brand new LMS High Torque Mini Mill (PN: 3900) as part of an upgrade. Complete assembly, comes with mounting bolts. Includes the following parts (Total value of $87.45): Retainer (PN: 1458, $12.77) Spring (PN: 1459, $7.06) Support (PN: 1462, $7.06) Shaft - Can ya dig it?

This is a Quick-Grip Screw-Clamp Saw / Sprocket Arbor Adapter used to fasten a saw blade or sprocket with a 1-3/8" bore onto a 1/2" diameter shaft. Here's how it works:1) Remove the clamping nut2) Slide the adapter into position on the 1/2" shaft3) Place the saw blade or sprocket (up to 1/4" thick) with a 1-3/8" bore onto the adapter4) Replace the clamping nut and tighten to secure onto the shaft This only takes a minute and you are ready to go! The nut is 1-5/8" across the flats and abou

FOR SALE ARE 440 BRAND NEW METAL BEARING BUSHING SPACER SLEEVES.THEY MEASURE 1/2 INCH LONG AND 5/16 OF AN INCH INSIDE HOLE.YOU WILL RECEIVE ALL 440 PIECES.You will not be disappointed.My feedback speaks for itself.If you have any questions please email me and please check out the other items i have for sale.If you have problems with your order,PLEASE CONTACT ME BEFORE LEAVING FEEDBACK.Thanks,mark ATTENSION ATTENSION /NOTICE NOTICE!!!

You are looking at 1 Fenner Drives Trantorque Keyless Bushing, 6202380, 1-7/16 shaft, New, without boxes. I have 3 of these available in this size only. What you see in the picture is EXACTLY what you are getting unless.

ECONOMY SHAFT BUSHING P-152-48 BUSHING 1-7/8 INCH ID 2-3/8 INCH OD GENERAL INFORMATION: MANUFACTURED BY: ECONOMY SHAFT BUSHING MANUFACTURER PART NUMBER: P-152-48 DESCRIPTION: ECONOMY SHAFT BUSHING P-152-48 BUSHING 1-7/8 INCH ID 2-3/8 INCH OD 3 INCH LENGTH CONDITION:FNAP - THIS IS A NEW ITEM IN AUTOMATION RECOVERY PACKAGING. THE ITEM MAY HAVE BEEN OPENED BUT HAS NOT BEEN USED.IF YOU HAVE ANY QUESTIONS PLEASE CALL! (586) 741-5274

New - Browning Split Taper Bushing R1 2-7/8” Manufacturer: Browning Manufacturer Part Number: R1 2-7/8” Original Packaging: yes Hardware Included:

New stock just arrived! New Fenner Drives B-LOC Keyless Bushing Part #: T621025 Shaft Size: 25 mm Installation Torque: 12 ft-lbs See pictures for further specifications. Original manufacturer's packaging.

This is a 3030 taper lock bushing I took off a pulley on my Ag sprayer. It's dirty, but otherwise in good shape. It measures about 4.25" in diameter on the big end and about 3.75" in diameter on the small end (see pics).