shaft rollers for sale | 479 ads for brand-new and used shaft rollers

Angle round roll bender bending dies tooling for 1" tube 50mm shaft machine

Mira Loma, California, United States
Jun 1st

Set round roll bender tooling for 50mm shaft machine 1.5" o.d. round tube

Mira Loma, California, United States
Jun 1st

1 set round roll bender tooling for 50mm shaft machine 1.25" sch.40 pipe 1.660"

Mira Loma, California, United States
Jun 1st

25 huck 5/8" magnagrip rivet collars shaft spacers rollers bushings mcg-r20ul

Springfield, Tennessee, United States
US $14.99
Jan 29th

1738UC9C.2.98 New Huck Magna-Grip Rivet Collars, Part Number MCG-R20UL. Each bid quantity is for a Lot of Twenty-Five (25) Collars. You may bid / buy any number of lots, up to the total quantity available above.

5 national hardware v7601 1-7/8" roller,4 3/8"stem,7/16" shaft standard rollers

Mediapolis, Iowa, United States
Jan 30th

for your consideration 5 national hardware standard rollers size 1 7/8 rollers 4 3/8 stem 7/16 shaft some packages coming open but still new

Rubber coated rollers - 1.5 inch diameter - 10 rollers

Gurnee, Illinois, United States
US $34.50
Jan 30th

Ten (10) Rubber Rollers - 1-1/2" Diameter Rubber Rollers on a 1/2" Aluminum Shaft. This auction is for a collection of ten (10) of these used rollers, that are in great condition, with no nicks, cuts, or dried out sections. These are each 19-3/4" long Rubber Rollers, mounted or pressed onto a 22-3/8" long, 1/2" diameter Aluminum shaft.

National hardware v7601 1-7/8-inch roller 4-3/8-inch stem 7/16-inch shaft stand

Isanti, Minnesota, United States
US $15.00
Feb 28th

National Hardware V7601 1-7/8-Inch Roller 4-3/8-Inch Stem 7/16-Inch Shaft Standard Rollers, Plain Steel Garage Door Rollers (2-Pack) have a stem diameter of 7/16 in. and are 4-3/8 in. long.

Set round roll bender tooling for 50mm shaft machine 2" o.d. round tube 2.00"

Mira Loma, California, United States
Jun 1st

66 super heavy duty replacement gravity conveyor rollers 2.5" x 23" 11/16" shaft

Friendship, Wisconsin, United States
Jun 9th

66 Super Heavy Duty Conveyor Rollers 2.5" Diameter Fits between 23" conveyor rails 22" Face on roller 22-3/4" including hub 25" Overall length including axle shaft 11/16" Hex Shaft Approx 10 lbs per roller. Lot contains 66 rollers Due to the size / weight of this item, it is being shipped via freight. For a freight quote, or any questions, please email or call Delaney's Surplus at 608-643-8009 Closed Tuesdays and Wednesdays.

National hardware v7602 -7/8-inch roller 4-3/8-inch stem 7/16-inch shaft stand

Isanti, Minnesota, United States
Jun 9th

National Hardware V7602 1-7/8-Inch Roller 4-3/8-Inch Stem 7/16-Inch Shaft Heavy Duty Rollers, Plain Steel Garage Door Rollers (2-Pack) have a stem diameter of 7/16 in. and are 4-3/8 in. long.

Van norman no.12 milling machine

Willow Grove, Pennsylvania, United States
US $479.00
Feb 16th

VAN NORMAN No.12 Milling Machine 17" X travel 6-1/2" Y travel 12-1/8"spindle to table vertical mode 17" spindle to table horizontal mode 8 X 37-1/2 table Spindle taper changed to R-8 (to accommodate tooling from Bridgeport machines) 230-volt single-phase motor (Visible on top in main photo. It has a smaller drive pulley than the original motor.) Serial no. 5128-12 Made in 1937 The Table Vise that may or may not appear in the photos is NOT included.

Ralph-pughs 1.9" x 16" conveyor roller package of 10 pcs

Sauk Centre, Minnesota, United States
US $55.00
Jan 30th

These Ralph-Pugh rollers measure 16” inches long and 1.9” inches in diameter. They have a Spring loaded 5/16” hex shaft. Rollers have been packed into boxes without covering, They have collected dust and some surface rust on shaft but only cosmetic.